- 您现在的位置：买卖IC网 > PDF目录371822 > HIP6500BEVAL1 (Intersil Corporation) Multiple Linear Power Controller with ACPI Control Interface PDF资料下载
参数资料
| 型号： | HIP6500BEVAL1 |
| 厂商： | Intersil Corporation |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | Multiple Linear Power Controller with ACPI Control Interface |
| 中文描述： | 多重线性电源控制器ACPI控制接口 |
| 文件页数： | 10/15页 |
| 文件大小： | 156K |
| 代理商： | HIP6500BEVAL1 |
10
SOFT-START INTO ACTIVE STATES (S0, S1)
If both S3 and S5 are logic high at the time the 5VSB is
applied, the HIP6500B will assume active state wake-up and
keep off the controlled external transistors and the VCLK
output until some time (typically 25ms) after the ATX’s main
outputs used by the application (3.3V, 5V, and 12V) exceed
the set thresholds. This time-out feature is necessary in order
to insure the main ATX outputs are stabilized. The time-out
also assures smooth transitions from sleep into active when
sleep states are being supported. 3.3V
SB
output, whose
operation is only dependent on 5VSB presence, will come up
right as bias voltage reaches POR level.
During sleep to active state transitions from conditions
where the outputs are initially 0V (such as S5 to S0 transition
with EN3VDL = 1 and EN5VDL = 0, or simple power-up
sequence directly into active state), the 3V
DUAL
and
5V
DUAL
outputs go through a quasi soft-start by being pulled
high through the body diodes of the N-Channel MOSFETs
connected between these outputs and the 3.3V and 5V ATX
outputs. Figure 10 shows this start-up.
5VSB is already present when the main ATX outputs are
turned on at time T0. As a result of +3.3V
IN
and +5V
IN
ramping up, the 3.3V
DUAL
and 5V
DUAL
output capacitors
charge up through the body diodes of Q3 and Q5,
respectively (see Figure 3). At time T1, all main ATX outputs
exceed the HIP6500B’s undervoltage thresholds, and the
internal 25ms (typical) timer is initiated. At T2 the time-out
initiates a soft-start, and the memory and clock outputs are
ramped-up, reaching regulation limits at time T3.
Simultaneous with the beginning of the memory and clock
voltage ramp-up, at time T2, the DLA pin is pulled high,
turning on Q3 and Q5 in the process, and bringing the
3.3V
DUAL
and 5V
DUAL
outputs in regulation. Shortly after
time T3, as the SS voltage reaches 2.75V, the soft-start
capacitor is quickly discharged down to approximately 2.45V,
where it remains until a valid sleep state request is received
from the system.
Fault Protection
All the outputs are monitored against undervoltage events. A
severe overcurrent caused by a failed load on any of the
outputs, would, in turn, cause that specific output to
suddenly drop. If any of the output voltages drop below 80%
(typical) of their set value, such event is reported by having
the FAULT/MSEL pin pulled to 5V. Additionally, exceeding
the maximum current rating of an integrated regulator
(output with pass regulator on chip) can lead to output
voltage drooping; if excessive, this droop can ultimately trip
the undervoltage detector and send a FAULT signal to the
computer system.
A FAULT condition occurring on an output when controlled
through an external pass transistor will only set off the
FAULT flag, and it will not shut off or latch off any part of the
circuit. A FAULT condition occurring on an output when
controlled through an internal pass transistor, will set off the
FAULT flag, and it will shut off the faulting regulator only. If
shutdown or latch off of the entire circuit is desired in case of
a fault, regardless of the cause, this can be achieved by
externally pulling or latching the SS pin low. Pulling the SS
pin low will also force the FAULT pin to go low and reset an
internally latched-off output.
Special consideration is given to the initial start-up sequence.
If, following a 5VSB POR event, the 3.3V
SB
output is ramped
up and is subject to an undervoltage event before the
remainder of the controlled voltages have been brought up,
then the FAULT output goes high and the entire IC latches off.
Latch-off condition can be reset by cycling the bias power
(5V
SB
). Undervoltage events on the 3.3V
SB
output at any
other times are handled according to the description found in
the second paragraph under the current heading.
Another condition that could set off the FAULT flag is chip
over-temperature. If the HIP6500B reaches an internal
temperature of 140
o
C (typical), the FAULT flag is set off, but
the chip continues to operate until the temperature reaches
155
o
C (typical), when unconditional shutdown of all outputs
takes place. Operation resumes at 140
o
C and the
temperature cycling occurs until the fault-causing condition
is removed.
In HIP6500B applications, loss of any one active ATX output
(3.3V
IN
, 5V
IN
, or 12V
IN
; as detected by the on-board voltage
monitors) during active state operation causes the chip to
switch to S5 sleep state, in addition to reporting the input UV
condition on the FAULT/MSEL pin. Exiting from this forced-
S5 state can only be achieved by returning the faulting input
voltage above its UV threshold, by resetting the chip through
removal of 5V
SB
bias voltage, or by bringing the SS pin at a
potential lower than 0.8V.
Output Voltages
The output voltages are internally set and do not require any
external components. Selection of the V
MEM
memory
FIGURE 11. 2.5/3.3V
MEM
OUTPUT VOLTAGE SELECTION
CIRCUITRY DETAILS
FAULT/MSEL
40
μ
A
+
-
+
-
0.2V
MEM VOLTAGE
SELECT COMP
R
SEL
R
SEL
1k
10k
V
MEM
2.5V
3.3V
5VSB
HIP6500B
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6500 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6500CB | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6500EVAL1 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6501 | Triple Linear Power Controller with ACPI Control Interface |
| HIP6501A | Triple Linear Power Controller with ACPI Control Interface(带ACPI控制接口的线性电源控制器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6500CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6500CB-TS2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6500EVAL1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiple Linear Power Controller with ACPI Control Interface |
| HIP6501 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
| HIP6501A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
发布紧急采购，3分钟左右您将得到回复。