- 您现在的位置：买卖IC网 > PDF目录67101 > HMC449 (HITTITE MICROWAVE CORP) 27000 MHz - 33000 MHz RF/MICROWAVE FREQUENCY DOUBLER PDF资料下载
参数资料
| 型号： | HMC449 |
| 厂商： | HITTITE MICROWAVE CORP |
| 元件分类： | 倍频器 |
| 英文描述： | 27000 MHz - 33000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| 封装： | 1.20 X 1.10 MM, 0.10 MM HEIGHT, DIE-4 |
| 文件页数： | 6/6页 |
| 文件大小： | 235K |
| 代理商： | HMC449 |
F
R
E
Q
U
E
NC
Y
MU
L
T
IP
L
IE
R
S
-
A
C
T
IV
E
-
C
H
IP
2
2 - 37
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should
be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the
surface of the substrate. One way to accomplish this is to attach the 0.102mm
(4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab)
which is then attached to the ground plane (Figure 2).
Microstrip substrates should be brought as close to the die as possible in order
to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3
mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12
mils) is recommended to minimize inductance on RF, LO & IF ports.
An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer
capacitor (mounted eutectically or by conductive epoxy) placed no further than
0.762mm (30 Mils) from the chip is recommended.
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip may have fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The
mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature
of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the
chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required
for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31mm (12 mils).
0.102mm (0.004”) Thick GaAs MMIC
Wire 3 mil Ribbon Bond
RF Ground Plane
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Ribbon Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
HMC449
v01.1007
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 27 - 33 GHz OUTPUT
相关PDF资料 |
PDF描述 |
|---|---|
| HMC457QS16GE | 1700 MHz - 2200 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| HMC464LP5E | 2000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC466LP4 | 6100 MHz - 6720 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| HMC470LP3TR | 0 MHz - 3000 MHz RF/MICROWAVE VARIABLE ATTENUATOR, 2 dB INSERTION LOSS-MAX |
| HMC470LP3ETR | 0 MHz - 3000 MHz RF/MICROWAVE VARIABLE ATTENUATOR, 2 dB INSERTION LOSS-MAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMC449_07 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT |
| HMC449_09 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT |
| HMC449LC3B | 制造商:Hittite Microwave Corp 功能描述:IC MULTIPLIER X2 BB 12SMD |
| HMC449LC3B_09 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 31 GHz OUTPUT |
| HMC44DRAH | 功能描述:CONN EDGECARD 88POS R/A .100 SLD RoHS:是 类别:连接器，互连式 >> Card Edge 系列:- 标准包装:1 系列:- 卡类型:非指定 - 双边 类型:母头 Number of Positions/Bay/Row:30 位置数:60 卡厚度:0.062"（1.57mm） 行数:2 间距:0.156"（3.96mm） 特点:- 安装类型:通孔 端子:焊接 触点材料:铜铍 触点表面涂层:金 触点涂层厚度:30µin（0.76µm） 触点类型：:环形波纹管 颜色:绿 包装:托盘 法兰特点:顶部安装开口，螺纹插件，4-40 材料 - 绝缘体:聚苯硫醚（PPS） 工作温度:-65°C ~ 150°C 读数:双 |
发布紧急采购，3分钟左右您将得到回复。