- 您现在的位置：买卖IC网 > PDF目录67101 > HMC606 (HITTITE MICROWAVE CORP) 2000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | HMC606 |
| 厂商： | HITTITE MICROWAVE CORP |
| 元件分类： | 放大器 |
| 英文描述： | 2000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| 封装： | 2.80 X 1.73 MM, 0.10 MM HEIGHT, PLASTIC, DIE-4 |
| 文件页数： | 6/6页 |
| 文件大小： | 317K |
| 代理商： | HMC606 |
L
O
W
N
O
IS
E
A
M
P
L
IF
IE
RS
-
C
H
IP
1
1 - 107
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accom-
plish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
Microstrip substrates should brought as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protec-
tive containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pick-
up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The
surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with electrically conductive epoxy. The mounting surface should
be clean and flat.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recom-
mended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on
the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
HMC606
v02.0109
GaAs InGaP HBT MMIC ULTRA LOW
PHASE NOISE, DISTRIBUTED AMPLIFIER, 2 - 18 GHz
相关PDF资料 |
PDF描述 |
|---|---|
| HMC637LP5 | 0 MHz - 6000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| HMC637LP5E | 0 MHz - 6000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| HMC639ST89E | 200 MHz - 4000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC685LP4E | 1700 MHz - 2200 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| HMC685LP4 | 1700 MHz - 2200 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMC606_09 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs InGaP HBT MMIC ULTRA LOW PHASE NOISE, DISTRIBUTED AMPLIFIER, 2 - 18 GHz |
| HMC606LC5 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs InGaP HBT MMIC ULTRA LOW PHASE NOISE, DISTRIBUTED AMPLIFIER, 2 - 18 GHz |
| HMC606LC5_08 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs InGaP HBT MMIC ULTRA LOW PHASE NOISE, DISTRIBUTED AMPLIFIER, 2 - 18 GHz |
| HMC606LC5TR | 制造商:Hittite Microwave Corp 功能描述:IC AMP LOW PHASE NOISE 32SMD |
| HMC606-SX | 功能描述:RF Amplifier IC Radar 2GHz ~ 18GHz Die 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 频率:2GHz ~ 18GHz P1dB:13dBm 增益:13dB 噪声系数:6.5dB RF 类型:雷达 电压 - 电源:5V 电流 - 电源:64mA 测试频率:12GHz ~ 18GHz 封装/外壳:模具 供应商器件封装:模具 标准包装:2 |
发布紧急采购，3分钟左右您将得到回复。