- 您现在的位置：买卖IC网 > Datasheet目录328 > IDT7035L20PFI (IDT, Integrated Device Technology Inc)IC SRAM 144KBIT 20NS 100TQFP Datasheet资料下载
参数资料
| 型号： | IDT7035L20PFI |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 17/19页 |
| 文件大小： | 0K |
| 描述： | IC SRAM 144KBIT 20NS 100TQFP |
| 标准包装： | 3 |
| 格式 - 存储器： | RAM |
| 存储器类型： | SRAM - 双端口，异步 |
| 存储容量： | 144K（8K x 18） |
| 速度： | 20ns |
| 接口： | 并联 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
| 其它名称： | 7035L20PFI |
IDT7035S/L
High-Speed 8K x 18 Dual-Port Static RAM
shared resource. The left processor can then either repeatedly request
that semaphore’s status or remove its request for that semaphore to
perform another task and occasionally attempt again to gain control of the
token via the set and test sequence. Once the right side has relinquished
the token, the left side should succeed in gaining control.
The semaphore flags are active LOW. A token is requested by writing
a zero into a semaphore latch and is released when the same side writes
a one to that latch.
The eight semaphore flags reside within the IDT7035 in a separate
memory space from the Dual-Port RAM. This address space is accessed
by placing a LOW input on the SEM pin (which acts as a chip select for the
semaphore flags) and using the other control pins (Address, OE , and
R/ W ) as they would be used in accessing a standard Static RAM. Each
of the flags has a unique address which can be accessed by either side
through address pins A 0 – A 2 . When accessing the semaphores, none
of the other address pins has any effect.
When writing to a semaphore, only data pin D 0 is used. If a low level
is written into an unused semaphore location, that flag will be set to a zero
on that side and a one on the other side (see Truth Table V). That
semaphore can now only be modified by the side showing the zero. When
a one is written into the same location from the same side, the flag will be
set to a one for both sides (unless a semaphore request from the other side
is pending) and then can be written to by both sides. The fact that the side
which is able to write a zero into a semaphore subsequently locks out writes
from the other side is what makes semaphore flags useful in interprocessor
communications. (A thorough discussion on the use of this feature follows
shortly.) A zero written into the same location from the other side will be
stored in the semaphore request latch for that side until the semaphore is
freed by the first side.
When a semaphore flag is read, its value is spread into all data bits so
that a flag that is a one reads as a one in all data bits and a flag containing
a zero reads as all zeros. The read value is latched into one side’s output
register when that side's semaphore select ( SEM ) and output enable ( OE )
signals go active. This serves to disallow the semaphore from changing
state in the middle of a read cycle due to a write cycle from the other side.
Because of this latch, a repeated read of a semaphore in a test loop must
cause either signal ( SEM or OE ) to go inactive or the output will never
change.
A sequence WRITE/READ must be used by the semaphore in order
to guarantee that no system level contention will occur. A processor
requests access to shared resources by attempting to write a zero into a
semaphore location. If the semaphore is already in use, the semaphore
request latch will contain a zero, yet the semaphore flag will appear as one,
a fact which the processor will verify by the subsequent read (see Truth
Table V). As an example, assume a processor writes a zero to the left port
at a free semaphore location. On a subsequent read, the processor will
verify that it has written successfully to that location and will assume control
over the resource in question. Meanwhile, if a processor on the right side
attempts to write a zero to the same semaphore flag it will fail, as will be
verified by the fact that a one will be read from that semaphore on the right
side during subsequent read. Had a sequence of READ/WRITE been
used instead, system contention problems could have occurred during the
gap between the read and write cycles.
It is important to note that a failed semaphore request must be followed
by either repeated reads or by writing a one into the same location. The
reason for this is easily understood by looking at the simple logic diagram
Industrial and Commercial Temperature Ranges
of the semaphore flag in Figure 4. Two semaphore request latches feed
into a semaphore flag. Whichever latch is first to present a zero to the
semaphore flag will force its side of the semaphore flag LOW and the other
side HIGH. This condition will continue until a one is written to the same
semaphore request latch. Should the other side’s semaphore request latch
have been written to a zero in the meantime, the semaphore flag will flip
over to the other side as soon as a one is written into the first side’s request
latch. The second side’s flag will now stay LOW until its semaphore request
latch is written to a one. From this it is easy to understand that, if a semaphore
is requested and the processor which requested it no longer needs the
resource, the entire system can hang up until a one is written into that
semaphore request latch.
The critical case of semaphore timing is when both sides request a
single token by attempting to write a zero into it at the same time. The
semaphore logic is specially designed to resolve this problem. If simulta-
neous requests are made, the logic guarantees that only one side receives
the token. If one side is earlier than the other in making the request, the first
side to make the request will receive the token. If both requests arrive at
the same time, the assignment will be arbitrarily made to one port or the
other.
One caution that should be noted when using semaphores is that
semaphores alone do not guarantee that access to a resource is secure.
As with any powerful programming technique, if semaphores are misused
or misinterpreted, a software error can easily happen.
Initialization of the semaphores is not automatic and must be handled
via the initialization program at power-up. Since any semaphore request
flag which contains a zero must be reset to a one, all semaphores on both
sides should have a one written into them at initialization from both sides
to assure that they will be free when needed.
Using Semaphores—Some Examples
Perhaps the simplest application of semaphores is their application as
resource markers for the IDT7035’s Dual-Port RAM. Say the 8K x 18 RAM
was to be divided into two 4K x 18 blocks which were to be dedicated at
any one time to servicing either the left or right port. Semaphore 0 could
be used to indicate the side which would control the lower section of
memory, and Semaphore 1 could be defined as the indicator for the upper
section of memory.
To take a resource, in this example the lower 4K of Dual-Port RAM,
the processor on the left port could write and then read a zero in to
Semaphore 0. If this task was successfully completed (a zero was read
back rather than a one), the left processor would assume control
of the lower 4K. Meanwhile the right processor was attempting to gain
control of the resource after the left processor, it would read back a one
in response to the zero it had attempted to write into Semaphore 0. At this
point, the software could choose to try and gain control of the second 4K
section by writing, then reading a zero into Semaphore 1. If it succeeded
in gaining control, it would lock out the left side.
Once the left side was finished with its task, it would write a one to
Semaphore 0 and may then try to gain access to Semaphore 1. If
Semaphore 1 was still occupied by the right side, the left side could undo
its semaphore request and perform other tasks until it was able to write, then
read a zero into Semaphore 1. If the right processor performs a similar task
with Semaphore 0, this protocol would allow the two processors to swap
4K blocks of Dual-Port RAM with each other.
17
6.42
相关PDF资料 |
PDF描述 |
|---|---|
| IDT7037L20PFI | IC SRAM 576KBIT 20NS 100TQFP |
| IDT7038L15PFG | IC SRAM 1024KBIT 15NS 120TQFP |
| IDT7052L20G | IC SRAM 16KBIT 20NS 108PGA |
| IDT7054L20G | IC SRAM 32KBIT 20NS 108PGA |
| IDT709089L9PF | IC SRAM 512KBIT 9NS 100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT7035L20PFI8 | 功能描述:IC SRAM 144KBIT 20NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7035S15PF | 功能描述:IC SRAM 144KBIT 15NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7035S15PF8 | 功能描述:IC SRAM 144KBIT 15NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7035S20PF | 功能描述:IC SRAM 144KBIT 20NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7035S20PF8 | 功能描述:IC SRAM 144KBIT 20NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
发布紧急采购，3分钟左右您将得到回复。