- 您现在的位置：买卖IC网 > Datasheet目录328 > IDT7038L15PFG (IDT, Integrated Device Technology Inc)IC SRAM 1024KBIT 15NS 120TQFP Datasheet资料下载
参数资料
| 型号： | IDT7038L15PFG |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | IC SRAM 1024KBIT 15NS 120TQFP |
| 标准包装： | 12 |
| 格式 - 存储器： | RAM |
| 存储器类型： | SRAM - 双端口，异步 |
| 存储容量： | 1.125M（64K x 18） |
| 速度： | 15ns |
| 接口： | 并联 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
IDT7038L
High-Speed 64K x 18 Dual-Port Static RAM
Busy Logic
Busy Logic provides a hardware indication that both ports of the RAM
have accessed the same location at the same time. It also allows one of the
two accesses to proceed and signals the other side that the RAM is “busy”.
The BUSY pin can then be used to stall the access until the operation on
the other side is completed. If a write operation has been attempted from
the side that receives a BUSY indication, the write signal is gated internally
to prevent the write from proceeding.
The use of BUSY logic is not required or desirable for all applications.
In some cases it may be useful to logically OR the BUSY outputs together
and use any BUSY indication as an interrupt source to flag the event of
an illegal or illogical operation. If the write inhibit function of BUSY logic is
not desirable, the BUSY logic can be disabled by placing the part in slave
mode with the M/ S pin. Once in slave mode the BUSY pin operates solely
as a write inhibit input pin. Normal operation can be programmed by tying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
The BUSY outputs on the IDT7038 RAM in master mode, are push-
pull type outputs and do not require pull up resistors to operate. If these
RAMs are being expanded in depth, then the BUSY indication for the
resulting array requires the use of an external AND gate.
A 16
Industrial and Commercial Temperature Ranges
result in a glitched internal write inhibit signal and corrupted data in the
slave.
Semaphores
The IDT7038 is an extremely fast Dual-Port 64K x 18 CMOS Static
RAM with an additional 8 address locations dedicated to binary semaphore
flags. These flags allow either processor on the left or right side of the Dual-
Port RAM to claim a privilege over the other processor for functions defined
by the system designer’s software. As an example, the semaphore can
be used by one processor to inhibit the other from accessing a portion of
the Dual-Port RAM or any other shared resource.
The Dual-Port RAM features a fast access time, and both ports are
completely independent of each other. This means that the activity on the
left port in no way slows the access time of the right port. Both ports are
identical in function to standard CMOS Static RAM and can be read from,
or written to, at the same time with the only possible conflict arising from the
simultaneous writing of, or a simultaneous READ/WRITE of, a non-
semaphore location. Semaphores are protected against such ambiguous
situations and may be used by the system program to avoid any conflicts
in the non-semaphore portion of the Dual-Port RAM. These devices have
an automatic power-down feature controlled by CE , the Dual-Port RAM
enable, and SEM , the semaphore enable. The CE and SEM pins control
on-chip power down circuitry that permits the respective port to go into
MASTER
Dual Port RAM
CE 0
SLAVE
Dual Port RAM
CE 0
standby mode when not selected. This is the condition which is shown in
Truth Table II where CE and SEM are both HIGH.
BUSY L
BUSY R
BUSY L
BUSY R
Systems which can best use the IDT7038 contain multiple processors
or controllers and are typically very high-speed systems which are
Dual Port RAM
BUSY L BUSY R
MASTER CE 1
Dual Port RAM
BUSY L BUSY R
SLAVE CE 1
,
software controlled or software intensive. These systems can benefit from
a per-formance increase offered by the IDT7038s hardware sema-
phores, which provide a lockout mechanism without requiring complex
programming.
4837 drw 17
Figure 3. Busy and chip enable routing for both width and depth
expansion with IDT7038 RAMs.
Width Expansion Busy Logic
Master/Slave Arrays
When expanding an IDT7038 RAM array in width while using BUSY
logic, one master part is used to decide which side of the RAMs array will
receive a BUSY indication, and to output that indication. Any number of
slaves to be addressed in the same address range as the master, use
the BUSY signal as a write inhibit signal. Thus on the IDT7038 RAM the
BUSY pin is an output if the part is used as a master (M/ S pin = V IH ), and
the BUSY pin is an input if the part used as a slave (M/ S pin = V IL ) as shown
in Figure 3.
If two or more master parts were used when expanding in width, a split
decision could result with one master indicating BUSY on one side of the
array and another master indicating BUSY on one other side of the array.
This would inhibit the write operations from one port for part of a word and
inhibit the write operations from the other port for the other part of the word.
The BUSY arbitration, on a master, is based on the chip enable and
address signals only. It ignores whether an access is a read or write. In
a master/slave array, both address and chip enable must be valid long
enough for a BUSY flag to be output from the master before the actual write
pulse can be initiated with the R/ W signal. Failure to observe this timing can
Software handshaking between processors offers the maximum in
system flexibility by permitting shared resources to be allocated in varying
configurations. The IDT7038 does not use its semaphore flags to control
any resources through hardware, thus allowing the system designer total
flexibility in system architecture.
An advantage of using semaphores rather than the more common
methods of hardware arbitration is that wait states are never incurred in
either processor. This can prove to be a major advantage in very high-
speed systems.
How the Semaphore Flags Work
The semaphore logic is a set of eight latches which are independent
of the Dual-Port RAM. These latches can be used to pass a flag, or token,
from one port to the other to indicate that a shared resource is in use. The
semaphores provide a hardware assist for a use assignment method
called “Token Passing Allocation.” In this method, the state of a semaphore
latch is used as a token indicating that shared resource is in use. If the left
processor wants to use this resource, it requests the token by setting the
latch. This processor then verifies its success in setting the latch by reading
it. If it was successful, it proceeds to assume control over the shared
resource. If it was not successful in setting the latch, it determines that the
right side processor has set the latch first, has the token and is using the
shared resource. The left processor can then either repeatedly request
that semaphore’s status or remove its request for that semaphore to perform
another task and occasionally attempt again to gain control of the token via
15
6.42
相关PDF资料 |
PDF描述 |
|---|---|
| IDT7052L20G | IC SRAM 16KBIT 20NS 108PGA |
| IDT7054L20G | IC SRAM 32KBIT 20NS 108PGA |
| IDT709089L9PF | IC SRAM 512KBIT 9NS 100TQFP |
| IDT709099L9PFI | IC SRAM 1MBIT 9NS 100TQFP |
| IDT709149S10PFI | IC SRAM 36KBIT 10NS 80TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT7038L15PFG8 | 制造商:Integrated Device Technology Inc 功能描述:IC SRAM 1.125MBIT 15NS 100TQFP |
| IDT7038L20PF | 功能描述:IC SRAM 1.125MBIT 20NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，同步 存储容量:1.125M（32K x 36） 速度:5ns 接口:并联 电源电压:3.15 V ~ 3.45 V 工作温度:-40°C ~ 85°C 封装/外壳:256-LBGA 供应商设备封装:256-CABGA（17x17） 包装:带卷 (TR) 其它名称:70V3579S5BCI8 |
| IDT7038L20PF8 | 功能描述:IC SRAM 1.125MBIT 20NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，同步 存储容量:1.125M（32K x 36） 速度:5ns 接口:并联 电源电压:3.15 V ~ 3.45 V 工作温度:-40°C ~ 85°C 封装/外壳:256-LBGA 供应商设备封装:256-CABGA（17x17） 包装:带卷 (TR) 其它名称:70V3579S5BCI8 |
| IDT7038L20PFGI | 制造商:Integrated Device Technology Inc 功能描述:IC SRAM 1.125MBIT 20NS 100TQFP |
| IDT7038L20PFGI8 | 制造商:Integrated Device Technology Inc 功能描述:IC SRAM 1.125MBIT 20NS 100TQFP |
发布紧急采购，3分钟左右您将得到回复。