- 您现在的位置：买卖IC网 > PDF目录9970 > IDT82V2048BBG (IDT, Integrated Device Technology Inc)IC LIU T1/E1 8CH SHORT 160-BGA PDF资料下载
参数资料
| 型号： | IDT82V2048BBG |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 18/62页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1 8CH SHORT 160-BGA |
| 标准包装： | 14 |
| 类型： | 线路接口装置（LIU） |
| 规程： | E1 |
| 电源电压： | 3.13 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 160-BGA |
| 供应商设备封装： | 160-PBGA（15x15） |
| 包装： | 托盘 |
| 其它名称： | 82V2048BBG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
25
IDT82V2048 OCTAL T1/E1 SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
are configured properly. The required sequence for configuring the
Inband Loopback Generator is: First, set registers e-LBAC and e-LBDC,
followed by register e-LBCF. Then, to select the Inband Loopback
generator set registers e-LBGS and then e-LBGE.
The Inband Loopback Detection and the Inband Loopback Genera-
tion can not be used simultaneously.
Example: 5-bit Loop-up/Loop-down Detection (w/o interrupts):
(see note in register description for e-LBAC)
Loop-up code: 11000
Loop-down code: 11100
Set (in this order)
e-LBAC (0x09) = 0xC6 (11000110)
e-LBDC (0x0A) = 0xE7 (11100111)
e-LBCF (0x08) = 0x30
Example: 5-bit Loop-up/Loop-down Activation on Channel 1 (w/o
interrupts):
Loop-up code: 11000
Loop-down code: 11100
Set (in this order)
e-LBAC (0x09) = 0xC6 (11000110)
e-LBDC (0x0A) = 0xE7 (11100111)
e-LBCF (0x08) = 0x00
e-LBGS (0x0E) = 0x00
e-LBGE (0x0F) = 0x02
2.18 HOST INTERFACE
The host interface provides access to read and write the registers in
the device. The interface consists of serial host interface and parallel
host interface. By pulling pin MODE2 to VDDIO/2 or high, the device can
be set to work in serial mode and in parallel mode respectively.
2.18.1 PARALLEL HOST INTERFACE
The interface is compatible with Motorola and Intel host. Pins
MODE1 and MODE0 are used to select the operating mode of the
parallel host interface. When pin MODE1 is pulled low, the host uses
separate address bus and data bus. When high, multiplexed address/
data bus is used. When pin MODE0 is pulled low, the parallel host inter-
face is configured for Motorola compatible hosts. When pin MODE0 is
pulled high, the parallel host interface is configured for Intel compatible
hosts. See Table-1 Pin Description for more details. The host interface
pins in each operation mode is tabulated in Table-14:
Figure-22 Serial Host Mode Timing
2.18.2 SERIAL HOST INTERFACE
By pulling pin MODE2 to VDDIO/2, the device operates in the serial
host Mode. In this mode, the registers are accessible through a 16-bit
word which contains an 8-bit command/address byte (bit R/W and 5-
address-bit A1~A5, A6 and A7 bits are ignored) and a subsequent 8-bit
data byte (D7~D0), as shown in Figure-22. When bit R/W is set to ‘1’,
data is read out from pin SDO. When bit R/W is set to ‘0’, data on pin
SDI is written into the register whose address is indicated by address
bits A5~A1. See Figure-22 Serial Host Mode Timing.
Table-14 Parallel Host Interface Pins
MODE[2:0]
Host Interface
Generic Control, Data and Output Pin
100
Non-multiplexed Motorola interface
CS, ACK, DS, R/W, AS, A[4:0], D[7:0], INT
101
Non-multiplexed Intel interface
CS, RDY, WR, RD, ALE, A[4:0], D[7:0], INT
110
Multiplexed Motorola interface
CS, ACK, DS, R/W, AS, AD[7:0], INT
111
Multiplexed Intel interface
CS, RDY, WR, RD, ALE, AD[7:0], INT
A1
A3
A2
A4 A5 A6
D0 D1 D2 D3 D4 D5 D6 D7
R/W
D0 D1 D2 D3 D4 D5 D6 D7
A7
Input Data Byte
Address/Command Byte
High Impedance
Driven while R/W=1
SDI
SDO
SCLK
CS
1
22
1. While R/W=1, read from IDT82V2048; While R/W=0, write to IDT82V2048.
2. Ignored.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72V3640L6BB | IC FIFO SS 1024X36 6NS 144-BGA |
| MS27508E10B35SD | CONN RCPT 13POS BOX MNT W/SCKT |
| IDT82V2048BB | IC LIU T1/E1 8CH SHORT 160-BGA |
| IDT72T3645L6-7BB | IC FIFO 1024X36 6-7NS 208-BGA |
| MAX11208AEUB+T | IC ADC 19BIT SRL 120SPS 10UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT82V2048DA | 功能描述:IC LIU T1/E1 8CH SHORT 144-TQFP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2048DAG | 功能描述:IC LIU T1/E1 8CH SHORT 144-TQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2048E | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:OCTAL CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT |
| IDT82V2048EBB | 功能描述:IC LIU T1/E1 8CH SHORT 208-BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2048EBBG | 功能描述:IC LINE INTERFACE UNIT 208-PBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:2,500 系列:- 类型:驱动器 驱动器/接收器数:4/0 规程:RS422 电源电压:4.5 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。