- 您现在的位置：买卖IC网 > PDF目录1924 > IDT82V2604BBG (IDT, Integrated Device Technology Inc)IC INVERSE MUX 4CH ATM 208-BGA PDF资料下载
参数资料
| 型号： | IDT82V2604BBG |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 22/97页 |
| 文件大小： | 0K |
| 描述： | IC INVERSE MUX 4CH ATM 208-BGA |
| 标准包装： | 1 |
| 应用： | 无线 |
| 接口： | Utopia |
| 电源电压： | 2.97 V ~ 3.63 V |
| 封装/外壳： | 208-BGA |
| 供应商设备封装： | 208-PBGA（17x17） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
| 其它名称： | 82V2604BBG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
IMA AND UNI FUNCTIONS
29
December 4, 2006
IDT82V2604
Inverse Multiplexing for ATM
4
IMA AND UNI FUNCTIONS1
The IDT82V2604 is capable of combining the transport bandwidth of
multiple links into one single logical link. The logical link is called a
group. The IDT82V2604 supports up to 4 independent groups with each
group capable of supporting from 1 to 4 links. Links that are assigned to
an IMA group are called in IMA mode while links that are not assigned to
any IMA group can be used in UNI mode.
4.1
IMA MODE
4.1.1
IMA FRAME
An IMA frame is defined as M consecutive cells, numbered from 0 to
M-1 on each link, across all the links in an IMA group. It is generated by
inserting an ICP cell after every M-1 cells per link. Values of M supported
are 32, 64, 128 and 256, which can be programmed for all the links in a
group by ConfigGroupPara command. The ICP cell occurs within the
frame at the ICP cell offset position and should be at the same position
throughout the frame. The ICP offset is programmable on a per-link
basis by AddTxLink command.
4.1.2
TRL (TIMING REFERENCE LINK)
Within an IMA group, a TRL should be selected to pass synchroniza-
tion from the transmit to the receive end. The TRL can be selected by
ConfigTRLLink command.
4.1.3
STUFFING MODE
The insertion of stuff cells is to compensate for timing differences
between links within an IMA group.
There are two kinds of stuffing method: CTC (Common Transmit
Clock) mode and ITC (Independent Transmit Clock) mode. The stuffing
method is selected by ConfigGroupWorkMode command.
In CTC mode, a stuff cell is added after every 2048 ICP, filler and
ATM layer cells. The stuff cell is generated by repeating the ICP cell.
Both the ICP cell and the stuff cell are identified as ICP cells via the Link
Stuff Indication (LSI) field of the ICP cell. The stuff cell event will occur
on the same frame on all the links. However, the pre-defined ICP offset
will determine at which cell in the frame the stuff event will occur.
In ITC mode, a stuff cell is added to the TRL the same way as in CTC
mode, that is, it is added after every 2048 ICP, filler and ATM layer cells.
On all other links in the group, stuff cells are added as necessary to
compensate for timing differences between the TRL and other links of
the group.
In an IMA group, if at least one of the links uses independent clock
pin as its clock input, stuff mode can only be set as ITC. If all the links
within the group use common clock pin (i.e., TSCCK and RSCCK) as
their clock input, stuff mode can be set as either CTC or ITC. For details
about the two clock modes, please refer to 3.2.2 Line Interface Timing
4.1.4
LINK BACKUP
The group link backup function is used to add a link to the group for
backup in case of link failure. This function is only enabled when the
device is working in symmetry mode.
The link to be added to the group is specified as backup link or non-
backup link in ‘AddLink’ command (i.e., AddTxLink and AddRxLink
commands). Note that only one backup link is supported in each group.
If several links are specified as backup links, only the last added backup
link is regarded as a backup link.
When a link failure event occurred, the IDT82V2604 will automati-
cally pick up a backup link and activate it.
4.2
UNI MODE
ConfigDev command and ConfigUNILink command are used to
configure a UNI link. ConfigDev command can be used to configure TC
Work Mode, TC Alpha and Delta value and LCD threshold. ConfigU-
NILink command can be used to configure link physical ID, Tx and Rx
Utopia port, line interface Work Mode and clock mode.
When a link is configured in UNI mode, IMA functions are bypassed.
ATM cells are simply transmitted from the Utopia interface to the line
interface.
1. Chapter 4, 5, 6 and 7 are specific to IMAOS04. Details about
IMAOS04_Slave are provided in Chapter 8.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT82V2608BBG | IC INVERSE MUX 8CH ATM 208-BGA |
| IDT82V2616BBG | IC INVERSE MUX 16CH ATM 272-PBGA |
| IDT88K8483BRI | IC SPI-4 EXCHANGE 3PORT 672-BGA |
| IDT88P8341BHI | IC SPI3-SPI4 EXCHANGE 820-PBGA |
| IDT88P8342BHI | IC SPI3-SPI4 EXCHANGE 820-PBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT82V2608 | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:INVERSE MULTIPLEXING FOR ATM |
| IDT82V2608BB | 功能描述:IC INVERSE MUX 8CH ATM 208-BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| IDT82V2608BBG | 功能描述:IC INVERSE MUX 8CH ATM 208-BGA RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| IDT82V2616 | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:INVERSE MULTIPLEXING FOR ATM |
| IDT82V2616BB | 功能描述:IC INVERSE MUX 16CH ATM 272-PBGA RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
发布紧急采购，3分钟左右您将得到回复。