参数资料
| 型号： | IR3092M |
| 厂商： | International Rectifier |
| 文件页数： | 14/37页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER 2PHASE 48-MLPQ |
| 标准包装： | 100 |
| 应用： | VID 电压编程器 |
| 电源电压： | 7.3 V ~ 21 V |
| 电流 - 电源： | 29mA |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-MLPQ |
| 供应商设备封装： | 48-MLPQ（7x7） |
| 包装： | 剪切带 (CT) |
| 其它名称： | *IR3092M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
range. An 80k ? UHVLVWRU LV FRQQHFWHG DFURVV WKH *$7(; DQG 3*1'; SLQV WR SUHYHQW WKH *$7(; YROWDJH IURP ULVLQJ GXH
A Body Braking
Disable Comparator has been included to prevent false OVP firing during dynamic VID down changes.
The BB DISABLE Comparator disables Body Braking
when FB exceeds VDAC by 80mV. The low side MOSFETs will
IR3092
Power Good Output
The PWRGD pin is an open-collector output and should be pulled up to a voltage source through a resistor. During soft
start, the PWRGD remains low until the output voltage is in regulation and SS/DEL is above 3.75V. The PWRGD pin
becomes low if the fault latch is set. A high level at the PWRGD pin indicates that the converter is in operation and has no
fault, but does not ensure the output voltage is within the specification. Output voltage regulation within the design limits
can logically be assured however, assuming no component failure in the system.
Tri-State Gate Drivers
The gate drivers can deliver over 3.5A peak current. An adaptive non-overlap circuit monitors the voltage on the GATEHX
and GATELX pins to prevent MOSFET shoot-through current while minimizing body diode conduction.
The Error Amplifier output of the Control IC drives low in response to any fault condition such as VCC input under voltage
or output overload. The 0% duty cycle comparator detects this and drives both gate outputs low. This tri-state operation
prevents negative inductor current and negative output voltage during power-down.
The Gate Drivers revert to a hi gh impedance “off” state at VCCL and VCCHX supply voltages below the normal operating
to leakage or other cause under these conditions.
Over Voltage Protection (OVP)
The output Over-Voltage Protection comparator monitors the output voltage through the FB pin, the positive remote
sense point. If FB exceeds VDAC plus 145mV (for VR10.X, 480mV for OPTERON and ATHLON, selected with the
VID_SEL pin), both GATEL pins drive high and the OVP pin sources up to 10mA. The OVP circuit over-rides the normal
PWM operation and will fully turn-on the low side MOSFET within approximately 150ns. The low side MOSFET will
remain ON until the over-voltage condition ceases. The lower MOSFETs alone can not clamp the output voltage however
an SCR or N-MOSFET could be triggered by the OVP pin to prevent processor damage.
Error Amplifier compensation can slow down the response to an OVP condition if the voltage loop is too slow, which is
usually not the case. The FB pin can only respond to an over-voltage condition once the EAOUT voltage has reached its
minimum. Until then, the FB pin is modified by the falling EAOUT voltage so FB is equal to VDAC. The Error Amplifier
compensation slew current generates a voltage across the RFB resistor that will mask the output voltage OVP condition.
Again, for a typical fast voltage loop compensation scheme, a fairly large resistor is placed in series with the EAOUT to
FB compensation capacitor to speed up the loop which results in no noticeable OVP sensing delay.
The overall system must be considered when designing for OVP. In many cases the over-current protection of the AC-DC
or DC-DC converter supplying the multiphase converter will be triggered thus providing effective protection without
damage as long as all PCB traces and components are sized to handle the worst-case maximum current. If this is not
possible, a fuse can be added in the input supply to the multiphase converter. One scenario to be careful of is where the
input voltage to the multiphase converter may be pulled below the level where the ICs can provide adequate voltage to
the low side MOSFET thus defeating OVP.
TM
TM
then be controlled to keep V(FB) and V(VOUT) within 80mV of V(VDAC), below the 150mV INTEL OVP trip point.
Page 14 of 37
06/25/04
相关PDF资料 |
PDF描述 |
|---|---|
| IR3093MTRPBF | IC CTLR 3PHASE VR10 48-MLQP |
| IR3094MPBF | IC REG CTRLR BUCK PWM VM 48MLPQ |
| IR3220S | IC H-BRIDGE 45V 6A 20SOIC |
| IR3310STRR | IC SWITCH HI-SIDE 1CH D2-PAK-5 |
| IR3311STRR | IC SWITCH HI SIDE D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3092MPBF | 功能描述:IC VID VOLTAGE PROGRAMMER 48MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| IR3092MTR | 功能描述:IC CONTROLLER 2PHASE 48-MLPQ RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| IR3092MTRPBF | 功能描述:IC CONTROLLER 2PHASE 48-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| IR3093M | 制造商:IRF 制造商全称:International Rectifier 功能描述:3 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC |
| IR3093MPBF | 功能描述:IC VID VOLTAGE PROGRAMMER 48MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。