- 您现在的位置：买卖IC网 > PDF目录17761 > IS-C1603-CONTROLLER (NKK Switches)CTLR FOR 16 STD SMART SWITCHES PDF资料下载
参数资料
| 型号： | IS-C1603-CONTROLLER |
| 厂商： | NKK Switches |
| 文件页数： | 24/52页 |
| 文件大小： | 0K |
| 描述： | CTLR FOR 16 STD SMART SWITCHES |
| 标准包装： | 1 |
| 附件类型： | 控制器 |
| 适用于相关产品： | Standard SmartSwitch? |
| 配用： | IS15ABFP4B-ND - SMARTSWITCH STD BLK W/WHITE LED IS15ABDP4B-ND - SMARTSWITCH STD BLU W/WHITE LED IS15ABDP4EG-ND - SMARTSWITCH STD YELLOW/BLUE LED IS15ABDP4E-ND - SMARTSWITCH STD BLUE W/YEL LED IS15ABCP4EF-ND - SMARTSWITCH STD YEL/GRN LED IS15ABCP4E-ND - SMARTSWITCH STD LED YELLOW 360-2547-ND - SMARTSWITCH STD YEL RED/GRN LED 360-2332-ND - SMARTSWITCH STANDARD RED/GRN/BLU 360-2330-ND - SMARTSWITCH STD RED/GRN LED |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
IS-C1603 Intelligent Controller User
Manual
7850 East Gelding Drive ? Scottsdale, AZ 85260-3420
command format:
21H
[E1H]
[Timer value] [Timer value]
transmit format: (xxH) (xxAH) (xxAH) (xxAH)
[E1H] is one byte and must be sent in ASCII HEX format (45H 31H).
[Timer value] is one byte with value of 01H to FFH sent twice and must be sent in ASCII HEX format. The
default value is 40H.
Off Cycle Duration = 7 (Timer value) ms.
The controller responds with 61H and after processing the command 79H.
Command to set the time for LED’s ON Cycle duration.
LEDs are refreshed with two set of data sequentially. The two cycles are called “OFF cycle” and “ON cycle”.
The LED ON cycle time is determined according to the following formula:
LED ON time = (LED OFF time) x (Ratio -1)
If the ratio=1 then only LED OFF cycle will be shown. If the ratio=2 then LED ON cycle and LED OFF cycle
have equal time.
command format:
21H
[E2H]
[Ratio] [Ratio]
transmit format: (xxH) (xxAH) (xxAH) (xxAH)
[E2H] is one byte and must be sent in ASCII HEX format (45H 32H).
[Ratio] is one byte with value of 01H to FFH sent twice and must be sent in ASCII HEX format. The default
value is 03H.
The controller responds with 61H and after processing the command 79H.
Command to download maximum time between commands.
This command sets the timer value for the time between commands. It is used for real-time application. The
switches start blinking with red backlighting, if the timer expires before receiving the next command. The
blinking red notify the operator that there is an error and there is no communication with host.
command format:
21H
[E4H]
[Timer value] [Timer value]
transmit format: (xxH) (xxAH) (xxAH) (xxAH)
[E4H] is one byte and must be sent in ASCII HEX format (45H 34H).
[Timer value] is one byte sent twice and must be sent in ASCII HEX format. The default value is 80H.
The actual time is 20ms times this Timer value. To enable this feature, bit 7 of Flag-C must be enabled.
IS-C1603 Intelligent Controller User Manual D.doc
Toll Free 1.877.2BUYNKK (877.228.9655) ? Phone 480.991.0942 ? Fax 480.998.1435
www.nkkswitches.com ? Email engineering@nkkswitches.com
Page 24 of 52
0110
相关PDF资料 |
PDF描述 |
|---|---|
| 38EWSP71B4M6RT | SWITCH PUSH SPDT 0.4VA 20V |
| 38EWSP71B1M7RT | SWITCH PUSH SPDT 0.4VA 20V |
| 3314J-1-202G | TRIMMER 2K OHM 0.25W SMD |
| 3314J-1-201G | TRIMMER 200 OHM 0.25W SMD |
| CPPT8-LT0RT | OSC 3.3V PROG TTL TRI ST 25PPM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS-C1603H | 功能描述:交换机开发工具 RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| ISC1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
| ISC-1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。