- 您现在的位置：买卖IC网 > PDF目录17761 > IS-C1603-CONTROLLER (NKK Switches)CTLR FOR 16 STD SMART SWITCHES PDF资料下载
参数资料
| 型号： | IS-C1603-CONTROLLER |
| 厂商： | NKK Switches |
| 文件页数： | 29/52页 |
| 文件大小： | 0K |
| 描述： | CTLR FOR 16 STD SMART SWITCHES |
| 标准包装： | 1 |
| 附件类型： | 控制器 |
| 适用于相关产品： | Standard SmartSwitch? |
| 配用： | IS15ABFP4B-ND - SMARTSWITCH STD BLK W/WHITE LED IS15ABDP4B-ND - SMARTSWITCH STD BLU W/WHITE LED IS15ABDP4EG-ND - SMARTSWITCH STD YELLOW/BLUE LED IS15ABDP4E-ND - SMARTSWITCH STD BLUE W/YEL LED IS15ABCP4EF-ND - SMARTSWITCH STD YEL/GRN LED IS15ABCP4E-ND - SMARTSWITCH STD LED YELLOW 360-2547-ND - SMARTSWITCH STD YEL RED/GRN LED 360-2332-ND - SMARTSWITCH STANDARD RED/GRN/BLU 360-2330-ND - SMARTSWITCH STD RED/GRN LED |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
IS-C1603 Intelligent Controller User
Manual
7850 East Gelding Drive ? Scottsdale, AZ 85260-3420
Flag Byte B bit settings:
B0=0 ---> When a new address is assigned to any switch due to attribute execution or command, the
Controller transfer the LCD/LED code from the address to LCD/LED codes refresh
Buffer.
B0=1 ---> Do not transfer LCD/LED codes from addresses.
B1=0 ---> Upon power up/ reboot, use the switches assigned addresses that were in effect before
power down/ reboot.
B1=1 ---> Upon power up/ reboot, use the addresses from Power-up look-up table.
B2=0 ---> Execute Attributes upon switch press event.
B2=1 ---> Execute Attributes upon switch release event.
B3=0 ---> No action.
B3=1 ---> While switch is pressed change the backlighting to user-defined color.
B5=0 ---> 79H is not transmitted upon completion of commands.
B5=1 ---> Upon completion of a command from host, the controller transmits 79H in XXH format.
B6=0 ---> 61H is not transmitted for acknowledging commands.
B6=1 ---> Upon receipt of a command byte (20H to 2FH) from host, the controller transmits 61H in
XXH format. Regardless of B6 setting, the controllers transmit 61H in respond to
Command 01H from host.
B4, B7 -->These two bits are for polling operation. Both bits must be set to 1 for proper operation.
Use XON and XOFF for communication. The controller stops transmitting upon
receiving 13H and resumes transmitting upon receiving 11H. The transmit buffer is 256
bytes. The data will be lost if more than 256 bytes is to be transmitted.
IS-C1603 Intelligent Controller User Manual D.doc
Toll Free 1.877.2BUYNKK (877.228.9655) ? Phone 480.991.0942 ? Fax 480.998.1435
www.nkkswitches.com ? Email engineering@nkkswitches.com
Page 29 of 52
0110
相关PDF资料 |
PDF描述 |
|---|---|
| 38EWSP71B4M6RT | SWITCH PUSH SPDT 0.4VA 20V |
| 38EWSP71B1M7RT | SWITCH PUSH SPDT 0.4VA 20V |
| 3314J-1-202G | TRIMMER 2K OHM 0.25W SMD |
| 3314J-1-201G | TRIMMER 200 OHM 0.25W SMD |
| CPPT8-LT0RT | OSC 3.3V PROG TTL TRI ST 25PPM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS-C1603H | 功能描述:交换机开发工具 RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| ISC1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
| ISC-1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。