- 您现在的位置：买卖IC网 > PDF目录17761 > IS-C1603-CONTROLLER (NKK Switches)CTLR FOR 16 STD SMART SWITCHES PDF资料下载
参数资料
| 型号： | IS-C1603-CONTROLLER |
| 厂商： | NKK Switches |
| 文件页数： | 31/52页 |
| 文件大小： | 0K |
| 描述： | CTLR FOR 16 STD SMART SWITCHES |
| 标准包装： | 1 |
| 附件类型： | 控制器 |
| 适用于相关产品： | Standard SmartSwitch? |
| 配用： | IS15ABFP4B-ND - SMARTSWITCH STD BLK W/WHITE LED IS15ABDP4B-ND - SMARTSWITCH STD BLU W/WHITE LED IS15ABDP4EG-ND - SMARTSWITCH STD YELLOW/BLUE LED IS15ABDP4E-ND - SMARTSWITCH STD BLUE W/YEL LED IS15ABCP4EF-ND - SMARTSWITCH STD YEL/GRN LED IS15ABCP4E-ND - SMARTSWITCH STD LED YELLOW 360-2547-ND - SMARTSWITCH STD YEL RED/GRN LED 360-2332-ND - SMARTSWITCH STANDARD RED/GRN/BLU 360-2330-ND - SMARTSWITCH STD RED/GRN LED |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
IS-C1603 Intelligent Controller User
Manual
7850 East Gelding Drive ? Scottsdale, AZ 85260-3420
Flag Byte C bit settings:
B0=0 ---> No transmission.
B0=1 ---> Upon switch release, transmit the assigned address of the switch in ASCII HEX format.
B1=0 ---> No transmission.
B1=1 ---> Upon switch release, transmit the assigned address’s user-defined Image release data
string.
B2=0 ---> No transmission.
B2=1 ---> Upon switch release, transmit the switch’s user-defined switch release data string.
B3=0 ---> Disable
B3=1 ---> Enable repeat sending of user-defined Image press data string while the switch is pressed.
For this feature to work in addition to this flag, Bit 3 of Flag-A has to be enabled and
there has to be proper data in the look-up table.
B4=0 ---> Normal communication.
B4=1---> Enable multi-drop. For RS422
The controllers ignore all the received data unless the communication is initiated. To
initiate communication FFH followed by the controller’s UNIT ID in HEX must be
received. After communication is initiated controller accept the commands normally. If
the controller receives an FEH the communication is terminated. Controller responses can
be controlled by enabling Bits 4&7 of FLAG-B.
B5
---> Reserved. Must be set to zero. RS422 future use.
B6=0 ---> Disable timer for command 26H.
B6=1 ---> Enable timer for command 26H. Controller starts the timer after each option if the timer is
expired before a new option or exit received, the controller terminates the command 26H
subroutine ant transmit 6EH. The timer is user defined. It is recommended during
operation this flag to be enabled.
B7=0 ---> Normal operation mode.
B7=1 ---> Continuous command operation mode. Turns the user-defined timer after each
command. If the timer expires before the controller receives the next command,
blinking red codes are put into the LCD/LED code refresh Buffer for all the switches.
This is for applications in which the host continuously communicates with the
controller. Blinking red indicate to the operator that controller is off line.
IS-C1603 Intelligent Controller User Manual D.doc
Toll Free 1.877.2BUYNKK (877.228.9655) ? Phone 480.991.0942 ? Fax 480.998.1435
www.nkkswitches.com ? Email engineering@nkkswitches.com
Page 31 of 52
0110
相关PDF资料 |
PDF描述 |
|---|---|
| 38EWSP71B4M6RT | SWITCH PUSH SPDT 0.4VA 20V |
| 38EWSP71B1M7RT | SWITCH PUSH SPDT 0.4VA 20V |
| 3314J-1-202G | TRIMMER 2K OHM 0.25W SMD |
| 3314J-1-201G | TRIMMER 200 OHM 0.25W SMD |
| CPPT8-LT0RT | OSC 3.3V PROG TTL TRI ST 25PPM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS-C1603H | 功能描述:交换机开发工具 RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| ISC1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
| ISC-1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。