参数资料
| 型号： | ISL12020MIRZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 14/34页 |
| 文件大小： | 0K |
| 描述： | IC RTC/CALENDAR TEMP SNSR 20DFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 250 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，夏令时，闰年，SRAM |
| 存储容量： | 128B |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-LFDFN 裸露焊盘 |
| 供应商设备封装： | 20-DFN（5.5x4.0） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
ISL12020M
21
FN6667.5
December 13, 2011
FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT (BTSR)
This bit controls the frequency of Temp Sensing and Correction.
BTSR = 0 default mode is every 10 minutes, BTSR = 1 is every
1.0 minute. Note that BTSE has to be enabled in both cases. See
Table 16.
The temperature measurement conversion time is the same for
battery mode as for VDD mode, approximately 22ms. The battery
mode current will increase during this conversion time to
typically 68A. The average increase in battery current is much
lower than this due to the small duty cycle of the ON-time versus
OFF-time for the conversion.
To figure the average increase in battery current, we take the
change in current times the duty cycle. For the 1 minute
temperature period the average current is as shown in
Equation 1:
For the 10 minute temperature period the average current is as
shown in Equation 2:
If the application has a stable temperature environment that
doesn’t change quickly, the 10 minute option will work well and
the backup battery lifetime impact is minimized. If quick
temperature variations are expected (multiple cycles of more
than 10° within an hour), then the 1 minute option should be
considered and the slightly higher battery current figured into
overall battery life.
GAIN FACTOR OF AT BIT (BETA<4:0>)
Beta is specified to take care of the Cm variations of the crystal.
Most crystals specify Cm around 2.2fF. For example, if Cm > 2.2fF,
the actual AT steps may reduce from 1ppm/step to approximately
0.80ppm/step. Beta is then used to adjust for this variation and
restore the step size to 1ppm/step.
BETA values are limited in the range from 01000 to 11111 as
settings in Equation 3:
where:
AT(max) = FOUT in ppm (at AT = 00H) and
AT(min) = FOUT in ppm (at AT = 3FH).
The BETA VALUES result is indexed in the right hand column and
the resulting Beta factor (for the register) is in the same row in
the left column.
The ISL12020M has a preset BETA value corresponding to the
crystal in the module. This value is recalled on initial power-up
and should never be changed for best temperature
compensation performance, although the user may override this
preset value if so desired.
The value for BETA should only be changed while the TSE (Temp
Sense Enable) bit is “0”. The procedure for writing the BETA
register involves two steps. First, write the new value of BETA with
TSE = 0. Then write the same value of BETA with TSE = 1. This will
insure the next temp sense cycle will use the new BETA value.
Final Analog Trimming Register (FATR)
This register shows the final setting of AT after temperature
correction. It is read-only; the user cannot overwrite a value to this
register. This value is accessible as a means of monitoring the
TABLE 16. FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT
BTSE
BTSR
TC PERIOD IN
BATTERY MODE
00
OFF
01
OFF
10
10 Minutes
11
1 Minute
I
BAT
0.022s
60s
------------------
=
68
A 250nA
=
(EQ. 1)
I
BAT
0.022s
600s
------------------
=
68
A 25nA
=
(EQ. 2)
BETA VALUES
AT max
AT min
–
/63
=
(EQ. 3)
TABLE 17. BETA VALUES
BETA<4:0>
AT STEP ADJUSTMENT
01000
0.5000
00111
0.5625
00110
0.6250
00101
0.6875
00100
0.7500
00011
0.8125
00010
0.8750
00001
0.9375
00000
1.0000
10000
1.0625
10001
1.1250
10010
1.1875
10011
1.2500
10100
1.3125
10101
1.3750
10110
1.4375
10111
1.5000
11000
1.5625
11001
1.6250
11010
1.6875
11011
1.7500
11100
1.8125
11101
1.8750
11110
1.9375
11111
2.0000
相关PDF资料 |
PDF描述 |
|---|---|
| ISL12022IBZ-T7A | IC RTC/CALENDAR TEMP SNSR 8SOIC |
| ISL12022MAIBZ | IC RTC/CALENDAR TEMP SNSR 20SOIC |
| ISL12022MIBZ-T7A | IC RTC/CALENDAR TEMP SNSR 20SOIC |
| ISL12022MIBZR5421 | IC RTC/CALENDAR TEMP SNSR 20SOIC |
| ISL12023IVZ | IC RTC/CLDR TEMP SNSR 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL12021 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock with On Chip Temp Compensation 【5ppm |
| ISL12021CVZ | 功能描述:IC RTC LP BATT BACK SRAM 14TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
| ISL12021IVZ | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock with On Chip Temp Compensation 【5ppm |
| ISL12022 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock with On Chip ±5ppm Temp Compensation |
| ISL12022IBZ | 功能描述:实时时钟 REAL TIME CLK/CLNDR W/TEMP COMP 8 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。