- 您现在的位置：买卖IC网 > PDF目录20330 > ISL6146AFUZ-T (Intersil)IC OR CTRLR N-CH 1CH 8MSOP PDF资料下载
参数资料
| 型号： | ISL6146AFUZ-T |
| 厂商： | Intersil |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC OR CTRLR N-CH 1CH 8MSOP |
| 标准包装： | 2,500 |
| 应用： | 电信/数据通信系统 |
| FET 型： | N 沟道 |
| 输出数： | 1 |
| 内部开关： | 无 |
| 延迟时间 - 关闭： | 65ns |
| 电源电压： | 1 V ~ 20 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ISL6146
Functional Description
Functional Overview
In a redundant power distribution system, similar potential and
parallel power supplies each contribute to the load current
through various active and passive current sharing schemes.
Typically OR-ing power diodes are used to protect against reverse
current flow in the event that one of the power supplies falls
below the common bus voltage or develops a catastrophic
failure. However, using a discrete OR-ing diode solution has some
significant drawbacks. The primary downside is the increased
power dissipation loss in the OR-ing diodes as system power
requirements increase. At the lowest voltages where the ISL6146
is designed for use, the voltage distribution losses across an
OR-ing diode can be a significant percentage, in some cases
approaching 70%. Another disadvantage when using an OR-ing
diode is failure to detect a shorted or opened current path, which
jeopardizes system power availability and reliability. An open
diode may reduce the system to a single point of failure while a
shorted diode eliminates the system’s power protection.
Using an active OR-ing FET controller, such as the ISL6146, helps
with these potential issues. The use of a low on-resistance FET as
the OR-ing component allows for a more efficient system design
as the voltage across the FET is much lower than that across a
forward biased diode. Additionally, the ISL6146 has a dedicated
fault (FAULT) output pin that indicates when there is a conditional
or FET fault short providing the diagnostic capability that a diode
is unable to.
The ISL6146 is designed to OR together voltages as low as 1V
when supplied with a separate bias supply of 3V or greater.
Otherwise, the ISL6146 is designed to be biased from and OR
voltages across the 3V to 20V nominal supply range.
In a single FET configuration as voltage is first applied to a VIN
pin, the FET body diode conducts providing all the ISL6146s
connected on a common bus circuit, bias via the VOUT pins. As
individual power supply voltages ramp up in excess of the rising
POR threshold, the ISL6146’s internal charge pump activates to
provide a floating gate drive voltage for the external N-channel
OR-ing MOSFET, thus turning the FETs on once V IN > V OUT . The
ISL6146 continuously monitors the drain and source of the
OR-ing FET and provides a reverse voltage (N-channel MOSFET
V OUT - V IN ) detection threshold (VR) that, when exceeded,
indicates a reverse current condition. Once this threshold is
exceeded, the ISL6146 turns off the OR-ing FET by pulling down
the GATE pin to GND. The ISL6146 also provides high speed
V OUT > V IN transient protection as in the case of a catastrophic
VIN failure. The ISL6146 additionally provides for adjustment of
the V IN - V OUT reverse voltage Vth(VR Vth) via the ADJ pin of the
ISL6146 with an external resistor to GND. This allows adjusting
the V IN - V OUT voltage threshold level to compensate for normal
system voltage fluctuations, thus eliminating unnecessary
reaction by the ISL6146.
The total V IN - V OUT VR Vth is the sum of both the internal offset
and the external programmed VR Vth.
17
In the event of a V OUT > V IN condition, the ISL6146 responds
either with a high or low current pull-down on the GATE pin
depending on whether the High Speed comparator (HSCOMP)
has been activated or not. The HSCOMP determines if the VR
occurred within 1 μ s, by continuously monitoring the FET VDS and
if so, the high pull-down current is used to turn off the OR-ing FET.
In the event of a falling VIN transition in <1 μ s, (i.e., a catastrophic
failure of the power source) the HSCOMP protects the common
bus from the individual faulted power supply short by turning off
the shorted supply’s OR-ing MOSFET in less than 300ns, ensuring
the integrity of the common bus voltage from reverse current to
the damaged supply.
Once the correct V IN > V OUT relationship is established again, the
ISL6146 again turns on the FET.
The FAULT pin is an open drain, active low output indicating that
a fault or specific condition has occurred, these include:
? GATE is OFF (GATE < V IN +0.2V). Lack of conduction, not a fault,
just not on. ISL6146D and ISL6146E do not respond to this
condition
? Faults resulting in V IN - V OUT > 0.57V when ON
? An open FET resulting in body diode conduction
? Excessive current through FET
? FET Faults monitored and reported include
- G-D, gate unable to drive to Q-pump voltage
- G-S, gate unable to drive to Q-pump voltage
- D-S shorts, when GATE is OFF VDS < 2V
- V IN < POR
- Missing V IN
- V IN shorted to GND
On the ISL6146C version, a conditional fault is also signalled if
the V IN is not within the programmed UVLO and OVP levels.
The ISL6146 has an on-chip over-temperature fault threshold of
~+140°C with a 20°C hysteresis. Although the ISL6146 itself
produces little heat, it senses the environment in which it is,
likely including a close by FET.
The ISL6146A/D and ISL6146B/E are functional variants with an
enabling input of either polarity. This feature is used when the
need to interrupt the current path via signaling is necessary. This
is accomplished by implementing two FETs in series so that there
is a body diode positioned to block current in either direction.
This functionality is considered an additional enhancement to
the OR-ing diode it replaces.
The ISL6146C employs the use of a programmable Undervoltage
Lock Out (UVLO) and a programmable Overvoltage Protection (OVP)
input. This allows the GATE to only turn-on when the monitored
voltage is between the programmed lower and upper levels. This
application would use the back-to-back FET configuration. In the
event that the current path does not need to be interrupted then the
EN, UVLO and OVP inputs can all be overridden.
The ISL6146D and ISL6146E are variants of the ISL6146A and
ISL6146B respectively, the difference being the former do not
respond to a nonconduction condition (when enabled and
VIN>VOUT, the GATE is not on) unlike the latter that do signal
a fault.
FN7667.4
April 26, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6146CFRZ-TK | IC OR CONTROLLER |
| ISL6146CFRZ-T | IC OR CONTROLLER |
| ISL6146CFRZ | IC OR CONTROLLER |
| ISL6146BFRZ-TK | IC OR CONTROLLER |
| ISL6146BFRZ-T | IC INTERFACE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6146AFUZ-T7A | 功能描述:热插拔功率分布 LWV ORING FET CNTRLR 8LD RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6146AFUZ-TK | 功能描述:IC OR CTRLR N-CH 1CH 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL6146B | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Voltage ORing FET Controller |
| ISL6146BEVAL1Z | 制造商:Intersil Corporation 功能描述:ISL6146B EVALUATION BOARD - 8 LEAD - MSOP - ROHS COMPLIANT - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL6146 制造商:Intersil 功能描述:ISL98003CNZ-EVALZ EVAL BRD RHS COMPLIA |
| ISL6146BFRZ | 功能描述:IC INTERFACE RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:* 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。