参数资料
| 型号： | ISL6237IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 19/35页 |
| 文件大小： | 0K |
| 描述： | IC MAIN PWR CTRLR QUAD 32-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 5.5 V ~ 25 V |
| 输出数： | 4 |
| 输出电压： | 多重 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
ISL6237
Typical Application Circuits
TABLE 1. LDO OUTPUT VOLTAGE TABLE (Continued)
The typical application circuits (Figures 62, 63 and 64)
generate the typical 5V/7A, 3.3V/11A, 1.25V/5A, static
voltage/10A, 1.5V/5A, and 1.05V/5A supplies found in a
LDO VOLTAGE
3.3V
CONDITIONS
LDOREFIN > VCC - 1V,
BYP < 3V
COMMENT
Internal LDO is
active.
notebook computer. The input supply range is 5.5V to 25V.
2 x LDOREFIN
0.35V < LDOREFIN < 2.25V Internal LDO is
K ( V OUT + I LOAD ? r DSON ( LOWERQ ) )
t ON = ------------------------------------------------------------------------------------------------------
Detailed Description
The ISL6237 dual-buck, BiCMOS, switch-mode power-
supply controller generates logic supply voltages for
notebook computers. The ISL6237 is designed primarily for
battery-powered applications where high efficiency and low-
quiescent supply current are critical. The ISL6237 provides a
pin-selectable switching frequency, allowing operation for
200kHz/300kHz, 400kHz/300kHz, or 400kHz/500kHz on the
SMPSs.
Light-load efficiency is enhanced by automatic Idle-Mode
operation, a variable-frequency pulse-skipping mode that
reduces transition and gate-charge losses. Each step-down,
power-switching circuit consists of two N-Channel
MOSFETs, a rectifier, and an LC output filter. The output
voltage is the average AC voltage at the switching node,
which is regulated by changing the duty cycle of the
MOSFET switches. The gate-drive signal to the N-Channel
high-side MOSFET must exceed the battery voltage, and is
provided by a flying-capacitor boost circuit that uses a 100nF
capacitor connected to BOOT_.
Both SMPS1 and SMPS2 PWM controllers consist of a triple-
mode feedback network and multiplexer, a multi-input PWM
comparator, high-side and low-side gate drivers and logic. In
addition, SMPS2 can also use REFIN2 to track its output from
0.5V to 2.5V. The ISL6237 contains fault-protection circuits
that monitor the main PWM outputs for undervoltage and
overvoltage conditions. A power-on sequence block controls
the power-up timing of the main PWMs and monitors the
outputs for undervoltage faults. The ISL6237 includes an
adjustable low drop-out linear regulator. The bias generator
blocks include the linear regulator, a 2V precision reference
and automatic bootstrap switchover circuit.
The synchronous-switch gate drivers are directly powered
from PVCC, while the high-side switch gate drivers are
indirectly powered from PVCC through an external capacitor
and an internal Schottky diode boost circuit.
An automatic bootstrap circuit turns off the LDO linear
regulator and powers the device from BYP if LDOREFIN is
set to GND or VCC. See Table 1.
TABLE 1. LDO OUTPUT VOLTAGE TABLE
active.
FREE-RUNNING, CONSTANT ON-TIME PWM
CONTROLLER WITH INPUT FEED-FORWARD
The constant on-time PWM control architecture is a
pseudo-fixed-frequency, constant on-time, current-mode
type with voltage feed forward. The constant on-time PWM
control architecture relies on the output ripple voltage to
provide the PWM ramp signal; thus the output filter
capacitor's ESR acts as a current-feedback resistor. The
high-side switch on-time is determined by a one-shot whose
period is inversely proportional to input voltage and directly
proportional to output voltage. Another one-shot sets a
minimum off-time (300ns typ). The on-time one-shot triggers
when the following conditions are met: the error comparator's
output is high, the synchronous rectifier current is below the
current-limit threshold, and the minimum off time one-shot
has timed out. The controller utilizes the valley point of the
output ripple to regulate and determine the off time.
On-Time One-Shot (t ON )
Each PWM core includes a one-shot that sets the high-side
switch on-time for each controller. Each fast, low-jitter,
adjustable one-shot includes circuitry that varies the on-time
in response to battery and output voltage. The high-side
switch on-time is inversely proportional to the battery voltage
as measured by the VIN input and proportional to the output
voltage. This algorithm results in a nearly constant switching
frequency despite the lack of a fixed-frequency clock
generator. The benefit of a constant switching frequency is
that the frequency can be selected to avoid noise-sensitive
frequency regions:
(EQ. 1)
V IN
See Table 2 for approximate K- factors. Switching frequency
increases as a function of load current due to the increasing
drop across the synchronous rectifier, which causes a faster
inductor-current discharge ramp. On-times translate only
roughly to switching frequencies. The on-times established in
the “Electrical Specifications” table on page 4 are influenced
by switching delays in the external high-side power MOSFET.
Also, the dead-time effect increases the effective on-time,
reducing the switching frequency. It occurs only in PWM mode
LDO VOLTAGE
CONDITIONS
COMMENT
(SKIP = VCC) and during dynamic output voltage transitions
when the inductor current reverses at light or negative load
VOLTAGE at BYP LDOREFIN < 0.3V,
BYP > 4.63V
VOLTAGE at BYP LDOREFIN > VCC - 1V,
BYP > 3V
Internal LDO is
disabled.
Internal LDO is
disabled.
currents. With reversed inductor current, the inductor's EMF
causes PHASE to go high earlier than normal, extending the
on-time by a period equal to the UGATE-rising dead time.
5V
LDOREFIN < 0.3V,
BYP < 4.63V
19
Internal LDO is
active.
FN6418.4
March 18, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6236AIRZ-T | IC MAIN PWR CTRLR QUAD 32-QFN |
| EBA32DTKT | CONN EDGECARD 64POS DIP .125 SLD |
| MIC5335-PGYMT TR | IC REG LDO 3V/1.8V .3A 6-MLF |
| ISL6236IRZA-TR5281 | IC MAIN PWR CTRLR QUAD 32-QFN |
| ESA18DTKS | CONN EDGECARD 36POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62381 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad or Triple-Output System Power Supply Controller for Notebook Computers |
| ISL62381CHRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381CHRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381HIEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62381HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62381HRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。