参数资料
| 型号： | ISL6237IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 29/35页 |
| 文件大小： | 0K |
| 描述： | IC MAIN PWR CTRLR QUAD 32-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 5.5 V ~ 25 V |
| 输出数： | 4 |
| 输出电压： | 多重 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页
ISL6237
negative current limit is met, UGATE is turned on for a
minimum on-time, followed by another LGATE pulse until
negative current limit. This effectively regulates the
discharge current at the negative current limit in an effort to
prevent excessively large negative currents that cause
potentially damaging negative voltages on the load. Once an
overvoltage fault condition is set, it can only be reset by
toggling SHDN, EN_, or cycling VIN (POR).
UNDERVOLTAGE PROTECTION
When the output voltage drops below 70% of its regulation
voltage for at least 100μs, the controller sets the fault latch
and begins the discharge mode (see the following Shutdown
and Output Discharge sections). UVP is ignored for at least
20ms (typical), after start-up or after a rising edge on EN_.
Toggle EN_ or cycle VIN (POR) to clear the undervoltage
fault latch and restart the controller. UVP only applies to the
buck outputs.
THERMAL PROTECTION
The ISL6237 has thermal shutdown to protect the devices
from overheating. Thermal shutdown occurs when the die
temperature exceeds +150°C. All internal circuitry shuts
down during thermal shutdown. The ISL6237 may trigger
thermal shutdown if LDO_ is not bootstrapped from OUT_
while applying a high input voltage on VIN and drawing the
maximum current (including short circuit) from LDO_. Even if
LDO_ is bootstrapped from OUT_, overloading the LDO_
causes large power dissipation on the bootstrap switches,
Discharge Mode (Soft-Stop)
When a transition to standby or shutdown mode occurs, or
the output undervoltage fault latch is set, the outputs
discharge to GND through an internal 25 Ω switch. The
reference remains active to provide an accurate threshold
and to provide overvoltage protection.
Shutdown Mode
The ISL6237 SMPS1, SMPS2 and LDO have independent
enabling control. Drive EN1, EN2 and EN_LDO below the
precise input falling-edge trip level to place the ISL6237 in its
low-power shutdown state. The ISL6237 consumes only
20μA of quiescent current while in shutdown. Both SMPS
outputs are discharged to 0V through a 25 Ω switch.
Power-Up Sequencing and On/Off Controls (EN_)
EN1 and EN2 control SMPS power-up sequencing. EN1 or
EN2 rising above 2.4V enables the respective outputs. EN1
or EN2 falling below 1.6V disables the respective outputs.
Connecting EN1 or EN2 to REF will force its outputs off while
the other output is below regulation. The sequenced SMPS
will start once the other SMPS reaches regulation. The
second SMPS remains on until the first SMPS turns off, the
device shuts down, a fault occurs or PVCC goes into
undervoltage lockout. Both supplies begin their power-down
sequence immediately when the first supply turns off. Driving
EN_ below 0.8V clears the overvoltage, undervoltage and
thermal fault latches.
which may result in thermal shutdown. Cycling EN_,
EN_LDO, or VIN (POR) ends the thermal-shutdown state.
TABLE 3. OPERATING-MODE TRUTH TABLE
MODE
Power-Up
Run
Overvoltage
Protection
Undervoltage
Protection
Discharge
Standby
Shutdown
Thermal Shutdown
CONDITION
PVCC < UVLO threshold.
EN_LDO = high, EN1 or EN2
enabled.
Either output > 111% (VOUT1) or
116% (VOUT2) of nominal level.
Either output < 70% of nominal after
20ms time-out expires and output is
enabled.
Either SMPS output is still high in
either standby mode or shutdown
mode
EN1, EN2 < startup threshold,
EN_LDO = High
EN1, EN2, EN_LDO = low
T J > +150°C
29
COMMENT
Transitions to discharge mode after a VIN POR and after REF becomes valid. LDO
and REF remain active.
Normal operation
LGATE_ is forced high. LDO and REF are active. Exited by a VIN POR, or by toggling
EN1 or EN2.
The internal 25 Ω switch turns on. LDO and REF are active. Exited by a VIN POR or
by toggling EN1 or EN2.
Discharge switch (25 Ω ) connects OUT_ to GND. One output may still run while the
other is in discharge mode. Activates when PVCC is in UVLO, or transition to UVLO,
standby, or shutdown has begun. LDO and REF active.
LDO and REF are active.
Discharge switch (25 Ω ) connects OUT_ to PGND. All circuitry off.
All circuitry off. Exited by VIN POR or cycling EN_.
FN6418.4
March 18, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6236AIRZ-T | IC MAIN PWR CTRLR QUAD 32-QFN |
| EBA32DTKT | CONN EDGECARD 64POS DIP .125 SLD |
| MIC5335-PGYMT TR | IC REG LDO 3V/1.8V .3A 6-MLF |
| ISL6236IRZA-TR5281 | IC MAIN PWR CTRLR QUAD 32-QFN |
| ESA18DTKS | CONN EDGECARD 36POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62381 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad or Triple-Output System Power Supply Controller for Notebook Computers |
| ISL62381CHRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381CHRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381HIEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62381HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62381HRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。