- 您现在的位置：买卖IC网 > PDF目录16719 > ISL62392HRTZ-T (Intersil)IC PWR SUPPLY CONTROLLER 28TQFN PDF资料下载
参数资料
| 型号： | ISL62392HRTZ-T |
| 厂商： | Intersil |
| 文件页数： | 14/21页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY CONTROLLER 28TQFN |
| 标准包装： | 6,000 |
| 应用： | 电源控制器 |
| 电源电压： | 5.5 V ~ 25 V |
| 电流 - 电源： | 150µA |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
ISL62391, ISL62392, ISL62391C, ISL62392C
PVCC is above the 4.2V VCC POR threshold, VCC will
1.5ms
t SOFTSTART
VO
VCC AND PVCC
EN
FB
switchover to PVCC internally.
After VIN is applied, the VCC start-up 3.6V voltage can be used
as the logic high signal of any of EN1, EN2 and LDO3EN to
enable PVCC if there is no other power supply on the board.
MOSFET Gate-Drive Outputs LGATE and UGATE
The ISL62391, ISL62392, ISL62391C and ISL62392C have
internal gate-drivers for the high-side and low-side N-
PGOOD
2.75ms
PGOOD DELAY
FIGURE 24. SOFT-START SEQUENCE FOR ONE SMPS
The PGOOD pin indicates when the converter is capable of
supplying regulated voltage. It is an undefined impedance if
V IN is not above the rising POR threshold or below the POR
falling threshold. When a fault is detected, the ISL62391,
ISL62392, ISL62391C and ISL62392C will turn on the open-
drain NMOS, which will pull PGOOD low with a nominal
impedance of 32 Ω. This will flag the system that one of the
output voltages is out of regulation.
Separate enable pins allow for full soft-start sequencing.
Because low shutdown quiescent current is necessary to
prolong battery life in notebook applications, the PVCC 5V
LDO is held off until any of the three enable signals (EN1,
EN2 or LDO3EN) are pulled high. Soft-start of all outputs will
only start until after PVCC is above the 4.2V POR threshold.
In addition to user-programmable sequencing, the ISL62391,
ISL62392, ISL62391C and ISL62392C include a pre-
programmed sequential SMPS soft-start feature. Table 1
shows the SMPS enable truth table.
TABLE 1. SMPS ENABLE SEQUENCE LOGIC
Channel MOSFETs. The low-side gate-drivers are optimized
for low duty-cycle applications where the low-side MOSFET
conduction losses are dominant, requiring a low r DS(ON)
MOSFET. The LGATE pull-down resistance is small in order
to clamp the gate of the MOSFET below the V GS(th) at turn-
off. The current transient through the gate at turn-off can be
considerable because the gate charge of a low r DS(ON)
MOSFET can be large. Adaptive shoot-through protection
prevents a gate-driver output from turning on until the opposite
gate-driver output has fallen below approximately 1V. The
dead-time shown in Figure 25 is extended by the additional
period that the falling gate voltage stays above the 1V
threshold. The typical dead-time is 21ns. The high-side gate-
driver output voltage is measured across the UGATE and
PHASE pins while the low-side gate-driver output voltage is
measured across the LGATE and PGND pins. The power for
the LGATE gate-driver is sourced directly from the PVCC pin.
The power for the UGATE gate-driver is sourced from a “boot”
capacitor connected across the BOOT and PHASE pins. The
boot capacitor is charged from the 5V PVCC supply through a
“boot diode” each time the low-side MOSFET turns on, pulling
the PHASE pin low. The ISL62391, ISL62392, ISL62391C and
ISL62392C have integrated boot diodes connected from the
PVCC pins to BOOT pins.
EN1
EN2
START-UP SEQUENCE
0
0
0
FLOAT
FLOAT
FLOAT
1
1
1
0
FLOAT
1
0
FLOAT
1
0
FLOAT
1
All SMPS outputs OFF
All SMPS outputs OFF
SMPS1 OFF, SMPS2 ON
All SMPS outputs OFF
All SMPS outputs OFF
SMPS1 enables after SMPS2 is in regulation
SMPS1 ON, SMPS2 OFF
SMPS2 enables after SMPS1 is in regulation
All SMPS outputs ON simultaneously
UGATE
LGATE
t LGFUGR
50%
50%
t UGFLGR
VCC
The VCC nominal operation voltage is 5V. If EN1, EN2 and
LDO3EN are all logic low, the VCC start-up voltage is 3.6V
when VIN is applied on ISL62391, ISL62392, ISL62391C
and ISL62392C. PVCC is held off until any of the three
enable signals (EN1, EN2 or LDO3EN) is pulled high. When
14
FIGURE 25. LGATE AND UGATE DEAD-TIME
Diode Emulation
FCCM is a logic input that controls the power state of the
ISL62391, ISL62392, ISL62391C and ISL62392C. If forced
high, the ISL62391, ISL62392, ISL62391C and ISL62392C
will operate in forced continuous-conduction-mode (CCM)
FN6666.7
August 22, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| GEA28DTMN | CONN EDGECARD 56POS R/A .125 SLD |
| MAX6164AESA | IC VREF SERIES PREC 4.096V 8SOIC |
| H3AAH-1036M | IDC CABLE - HSC10H/AE10M/HSC10H |
| REC5-0512DRW/H4/C | CONV DC/DC 5W 4.5-9VIN +/-12VOUT |
| MAX6163AESA | IC VREF SERIES PREC 3V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62392IRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 28TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62392IRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 28TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62392LOEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62392LO RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6244 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multi-Phase PWM Controller |
| ISL6244CR | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。