参数资料
| 型号： | ISL6263CHRZ-T |
| 厂商： | Intersil |
| 文件页数： | 16/18页 |
| 文件大小： | 0K |
| 描述： | IC VOLT REG 1PH 5BIT VID 32-QFN |
| 标准包装： | 6,000 |
| 应用： | 转换器，GPU 内核电源 |
| 输入电压： | 5 V ~ 25 V |
| 输出数： | 1 |
| 输出电压： | 0.41 V ~ 1.29 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 带卷 (TR) |
ISL6263C
Dynamic Mode of Operation - Compensation
Parameters
Intersil provides a spreadsheet to calculate the compensator
parameters. Caution needs to be used in choosing the input
resistor to the FB pin. Excessively high resistance will cause
an error to the output voltage regulation due to the bias
current flowing through the FB pin. It is recommended to
keep this resistor below 3k ? .
Layout Considerations
As a general rule, power should be on the bottom layer of
the PCB and weak analog or logic signals are on the top
layer of the PCB. The ground-plane layer should be adjacent
to the top layer to provide shielding.
Inductor Current Sense and the NTC Placement
It is crucial that the inductor current be sensed directly at the
PCB pads of the sense element, be it DCR sensed or discrete
resistor sensed. The effect of the NTC on the inductor DCR
thermal drift is directly proportional to its thermal coupling with
the inductor and thus, the physical proximity to it.
Signal Ground and Power Ground
The ground plane layer should have a single point connection
to the analog ground at the VSS pin. The VSS island should
be located under the IC package along with the weak analog
traces and components. The paddle on the bottom of the
ISL6263C QFN package is not electrically connected to the
IC, however, it is recommended to make a good thermal
connection to the VSS island using several vias. Connect the
input capacitors, the output capacitors, and the source of the
lower MOSFETs to the power ground plane.
LGATE, PVCC, and PGND
PGND is the return path for the pull-down of the LGATE
low-side MOSFET gate driver. Ideally, PGND should be
connected to the source of the low-side MOSFET with a
low-resistance, low-inductance path. The LGATE trace should
be routed in parallel with the trace from the PGND pin. These
two traces should be short, wide, and away from other traces
because of the high peak current and extremely fast dv/dt.
PVCC should be decoupled to PGND with a ceramic capacitor
physically located as close as practical to the IC pins.
UGATE, BOOT, and PHASE
PHASE is the return path for the entire UGATE high-side
MOSFET gate driver. The layout for these signals require
similar treatment, but to a greater extent, than those for
LGATE, PVCC, and PGND. These signals swing from
approximately VIN to VSS and are more likely to couple into
other signals.
VSEN and RTN
These traces should be laid out as noise sensitive. For
optimum load line regulation performance, the traces
connecting these two pins to the Kelvin sense leads of the
processor should be laid out away from rapidly rising voltage
nodes, (switching nodes) and other noisy traces. The filter
capacitors C FILTER1 , C FILTER2 , and C FILTER3 used in
conjunction with filter resistors R FILTER1 and R FILTER2 form
common mode and differential mode filters, as shown in
Figure 8. The noise environment of the application and
actual board layout conditions will drive the extent of filter
complexity. The maximum recommended resistance for
R FILTER1 and R FILTER2 is approximately 10 ? to avoid
interaction with the 50k ? input resistance of the remote
sense differential amplifier. The physical location of these
resistors is not as critical as the filter capacitors. Typical
capacitance values for C FILTER1 , C FILTER2 , and C FILTER3
range between 330pF to 1000pF and should be placed near
the IC.
RBIAS
The resistor R RBIAS should be placed in close proximity to
the ISL6263C using a noise-free current return path to the
VSS pin.
IMON, SOFT, OCSET, V W, COMP, FB, VDIFF,
ICOMP, ISP, ISN and VO
The traces and components associated with these pins
require close proximity to the IC as well as close proximity to
each other. This section of the converter circuit needs to be
located above the island of analog ground with the
single-point connection to the VSS pin.
Resistor R S
Resistor R S is preferably located near the boundary
between the power ground and the island of analog ground
VIAS TO
GROUND
PLANE
GND
OUTPUT
CAPACITORS
SCHOTTKY
connected to the VSS pin.
VID<0:4>, AF_EN, PGOOD, and VR_ON
These are logic signals that do not require special attention.
INDUCTOR
HIGH-SIDE
MOSFETS
VOUT
PHASE
NODE
VIN
DIODE
LOW-SIDE
MOSFETS
INPUT
CAPACITORS
FDE
This logic signal should be treated as noise sensitive and
should be routed away from rapidly rising voltage nodes,
(switching nodes) and other noisy traces.
FIGURE 10. TYPICAL POWER COMPONENT PLACEMENT
16
VIN
The VIN signal should be connected near the drain of the
high-side MOSFET.
FN6745.1
July 8, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6263CRZ | IC VREG CORE 5BIT 1PHASE 32-QFN |
| ISL6263DHRZ | IC VREG 3BIT 1PHASE 32-QFN |
| ISL6264CRZ | IC CORE CTRLR TWO-PHASE 40-QFN |
| ISL6265AHRTZ-T | IC CTRLR MULTI-OUTPUT 48-TQFN |
| ISL6265CHRTZ | IC CTRLR MULTI-OUTPUT 48TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6263CRZ | 功能描述:直流/直流开关调节器 1 PHS INT DC/DC BUCK CNTRLR FOR INTEL RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6263CRZ-T | 功能描述:直流/直流开关调节器 1 PHS INT DC/DC BUCK CNTRLR FOR INTEL RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6263DEVAL1Z | 功能描述:EVAL BAORD 1 FOR ISL6263D RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6263DHRZ | 功能描述:IC VREG 3BIT 1PHASE 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6263DHRZ-T | 功能描述:IC VREG 3BIT 1PHASE 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。