参数资料
| 型号： | ISL6266HRZ |
| 厂商： | Intersil |
| 文件页数： | 22/30页 |
| 文件大小： | 0K |
| 描述： | IC CORE CTRLR 2PHASE 48-QFN |
| 标准包装： | 43 |
| 应用： | 转换器，Intel IMVP-6 |
| 输入电压： | 5 V ~ 25 V |
| 输出数： | 1 |
| 输出电压： | 0.3 V ~ 1.5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页
ISL6266, ISL6266A
volt-second balance. The ISL6266 continues to turn on the
lower MOSFET for the inactive channel to deplete the induced
field with minimum power loss.
Component Selection and Application
The IMVP-6+ specification dictates the critical timing
associated with regulating the output voltage. The symbol,
SLEWRATE, as given in the IMVP-6+ specification will
determine the choice of the SOFT capacitor (C SOFT ) by
Equation 4.
C SOFT = ------------------------------------
Soft-Start and Mode Change Slew Rates
The ISL6266A uses two slew rates for various modes of
I GV
SLEWRATE
(EQ. 4)
operation. The first is a slow slew rate used to reduce in-rush
current during start-up. It is also used to reduce audible noise
when entering or exiting Deeper Sleep Mode. A faster slew rate
Using a SLEWRATE of 10mV/μs and the typical I GV value
given in the “Electrical Specifications” table on page 4 of
205μA, C SOFT is as shown in Equation 5.
is used to exit out of Deeper Sleep and to enhance system
performance by achieving active mode regulation more quickly.
C SOFT = 205 μ A ? ( 10mV ? 1 μ s )
(EQ. 5)
Note that the SOFT capacitor current is bidirectional. The
current is flowing into the SOFT capacitor when the output
voltage is commanded to rise and out of the SOFT capacitor
when the output voltage is commanded to fall.
Figure 36 illustrates how the two slew rates are determined
by commanding one of two current sources into or out of the
A choice of 0.015μF would guarantee a SLEWRATE of
10mV/μs is met for the minimum I GV value given in the
“Electrical Specifications” table on page 4. This choice of
C SOFT will then control the start-up slewrate as well. One
should expect the output voltage to slew to the boot value of
1.2V at a rate given by Equation 6.
dV I SS 41 μ A
0.015 μ F
C SOFT
SOFT pin. The capacitor from the SOFT pin to ground holds
the voltage commanded by the two current sources. The
voltage is fed into the non-inverting input of the error
------- = ------------------- = ----------------------- = 2.8mV ? μ s
dt
(EQ. 6)
amplifier and sets the regulated system voltage. Depending
on the state of the system (Start-Up or Active mode) and the
state of the DPRSLPVR pin, one of the two currents shown
in Figure 36 will be used to charge or discharge this
capacitor, thereby controlling the slew rate of the newly
commanded voltage. These currents can be found under
“SOFT-START CURRENT” on page 4 of the “Electrical
Specifications” table.
ISL6266, ISL6266A
Selecting RBIAS
To properly bias the ISL6266A, a reference current is
established by placing a 147k Ω , 1% tolerance resistor from
the RBIAS pin to ground. This will provide a highly accurate
10μA current source from which the OCSET reference
current can be derived.
Care should be taken in layout that the resistor is placed
very close to the RBIAS pin and that a good quality signal
ground is connected to the opposite side of the RBIAS
resistor. Do not connect any other components to this pin as
this would negatively impact performance. Capacitance on
this pin would create instabilities and should be avoided.
I SS
I 2
ERROR
AMPLIFIER
+
Start-Up Operation - CLK_EN# and PGOOD
The ISL6266A provides a 3.3V logic output pin for
CLK_EN#. The 3V3 pin allows for a system 3.3V source to
SOFT
+
be connected to separated circuitry inside the ISL6266A,
solely devoted to the CLK_EN# function. The output is a
3.3V CMOS signal with 4mA sourcing and sinking capability.
C SOFT
V REF
This implementation removes the need for an external
pull-up resistor on this pin, thereby removing a leakage path
from the 3.3V supply to ground when the logic state is low.
FIGURE 36. SOFT PIN CURRENT SOURCES FOR FAST AND
SLOW SLEW RATES
The first current, labeled I SS , is given in the “Electrical
Specifications” table on page 4 as 42μA. This current is used
during soft-start. The second current (I 2 ) sums with I SS to
get the larger of the two currents, labeled I GV in the
“Electrical Specifications” table on page 4. This total current
is typically 205μA with a minimum of 180μA.
22
The lack of superfluous current leakage paths serves to
prolong battery life. For noise immunity, the 3.3V supply
should be decoupled to digital ground rather than to analog
ground.
As mentioned in “Theory of Operation” on page 18,
CLK_EN# is logic level high at start-up until approximately
43μs after the V CC_CORE is in regulation at the Boot level.
Afterwards, CLK_EN# transitions low, triggering an internal
timer for the IMVP6_PWRGD signal. When the timer
reaches 6.8ms, IMVP-6_PWRGD will toggle high.
FN6398.3
June 14, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ABM28DTKN | CONN EDGECARD 56POS DIP .156 SLD |
| X40021S14I-AT1 | IC VOLTAGE MONITOR DUAL 14-SOIC |
| 2512-102K | INDUCTOR POWER 1.0UH MOLDED SMD |
| RCC65DCMD | CONN EDGECARD 130POS .100 WW |
| RCA43DTBI | CONN EDGECARD 86POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6266HRZ-T | 功能描述:IC CORE CTRLR 2PHASE 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6267 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiphase PWM Regulator for AMD Fusion Mobile CPUs |
| ISL6267EVAL1Z | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiphase PWM Regulator for AMD Fusion Mobile CPUs |
| ISL6267HRZ | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLR FOR AMD FUSION UP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6267HRZ-T | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLR FOR AMD FUSION UP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。