- 您现在的位置：买卖IC网 > PDF目录15200 > ISL62871HRUZ-T (Intersil)IC REG CTRLR BUCK PWM 16-TQFN PDF资料下载
参数资料
| 型号： | ISL62871HRUZ-T |
| 厂商： | Intersil |
| 文件页数： | 10/25页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 16-TQFN |
| 标准包装： | 3,000 |
| 系列： | Robust Ripple Regulator™ (R³) |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 100% |
| 电源电压： | 3.3 V ~ 25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -10°C ~ 100°C |
| 封装/外壳： | 16-UFQFN |
| 包装： | 带卷 (TR) |
ISL62871, ISL62872
BOOT (Pin 18)
Positive input supply for the UGATE high-side MOSFET gate
driver. The BOOT pin is internally connected to the cathode
of the Schottky boot-strap diode. Connect an MLCC
between the BOOT pin and the PHASE pin.
VCC (Pin 19)
Input for the IC bias voltage. Connect +5V to the VCC pin
and decouple with at least a 1μF MLCC to the GND pin. See
PVCC (Pin 20)
Input for the LGATE and UGATE MOSFET driver circuits.
The PVCC pin is internally connected to the anode of the
Schottky boot-strap diode. Connect +5V to the PVCC pin
and decouple with a 10μF MLCC to the PGND pin. See
ISL62871 Functional Pin Descriptions
GND (Pin 1)
IC ground for bias supply and signal reference.
EN (Pin 2)
Enable input for the IC. Pulling EN above the V ENTHR rising
threshold voltage initializes the soft-start sequence.
VID0 (Pin 3)
Logic input for setpoint voltage selector. Use to select
between the two setpoint reference voltages. External
reference input when enabled by connecting the SET0 pin to
the VCC pin.
SREF (Pin 4)
Soft-start and voltage slew-rate programming capacitor
input. Setpoint reference voltage programming resistor input.
Connects internally to the inverting input of the V SET voltage
setpoint amplifier. See Figure 9 on page 12 for capacitor and
resistor connections.
SET0 (Pin 5)
Voltage set-point programming resistor input. See Figure 9
on page 12 for resistor connection.
PGOOD (Pin 6)
Power-good open-drain indicator output. This pin changes to
high impedance when the converter is able to supply
regulated voltage. The pull-down resistance between the
PGOOD pin and the GND pin identifies which protective fault
FB (Pin 7)
Voltage feedback sense input. Connects internally to the
inverting input of the control-loop error amplifier. The
converter is in regulation when the voltage at the FB pin
equals the voltage on the SREF pin. The control loop
compensation network connects between the FB pin and the
converter output. See Figure 13 on page 17.
10
VO (Pin 8)
Output voltage sense input for the R 3 modulator. The VO pin
also serves as the reference input for the overcurrent
detection circuit. See Figure 10 on page 14.
OCSET (Pin 9)
Input for the overcurrent detection circuit. The overcurrent
setpoint programming resistor R OCSET connects from this
pin to the sense node. See Figure 10 on page 14.
PHASE (Pin 10)
Return current path for the UGATE high-side MOSFET
driver. V IN sense input for the R 3 modulator. Inductor current
polarity detector input. Connect to junction of output inductor,
high-side MOSFET, and low-side MOSFET. See “Application
UGATE (Pin 11)
High-side MOSFET gate driver output. Connect to the gate
terminal of the high-side MOSFET of the converter.
BOOT (Pin 12)
Positive input supply for the UGATE high-side MOSFET gate
driver. The BOOT pin is internally connected to the cathode
of the Schottky boot-strap diode. Connect an MLCC
between the BOOT pin and the PHASE pin.
VCC (Pin 13)
Input for the IC bias voltage. Connect +5V to the VCC pin
and decouple with at least a 1μF MLCC to the GND pin. See
PVCC (Pin 14)
Input for the LGATE and UGATE MOSFET driver circuits.
The PVCC pin is internally connected to the anode of the
Schottky boot-strap diode. Connect +5V to the PVCC pin
and decouple with a 10μF MLCC to the PGND pin. See
LGATE (Pin 15)
Low-side MOSFET gate driver output. Connect to the gate
terminal of the low-side MOSFET of the converter.
PGND (Pin 16)
Return current path for the LGATE MOSFET driver. Connect
to the source of the low-side MOSFET.
Setpoint Reference Voltage Programming
Voltage identification (VID) pins select user-programmed
setpoint reference voltages that appear at the SREF pin. The
converter is in regulation when the FB pin voltage (V FB )
equals the SREF pin voltage (V SREF .) The IC measures V FB
and V SREF relative to the GND pin, not the PGND pin. The
setpoint reference voltages use the naming convention
FN6707.0
August 14, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL88001IE22Z-TK | IC VOLT SUPERVISOR 2.19V SC-70 |
| ISL6439CBZ-T | IC REG CTRLR BUCK PWM VM 14-SOIC |
| ISL88001IE26Z-TK | IC VOLT SUPERVISOR 2.63V SC-70 |
| ISL88001IE23Z-TK | IC VOLT SUPERVISOR 2.32V SC-70 |
| ISL88001IE17Z-TK | IC VOLT SUPERVISOR 1.67V SC-70 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62872HRUZ | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:PWM DC/DC Controller With VID Inputs For Portable GPU Core-Voltage Regulator |
| ISL62872HRUZ-T | 功能描述:IC REG CTRLR BUCK PWM 20-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL62873 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:PWM DC/DC Controller with VID Inputs for Portable GPU Core-Voltage Regulator |
| ISL62873HRUZ-T | 功能描述:IC REG CTRLR BUCK PWM 16UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL62875 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:PWM DC/DC Controller with VID Inputs for Portable GPU Core-Voltage Regulator |
发布紧急采购，3分钟左右您将得到回复。