参数资料
| 型号： | ISL6307AIRZ |
| 厂商： | Intersil |
| 文件页数： | 32/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 48-QFN |
| 标准包装： | 43 |
| PWM 型： | 电压模式 |
| 输出数： | 6 |
| 频率 - 最大： | 275kHz |
| 占空比： | 66.7% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页
ISL6307A
0.6
0.4
0.2
I L,PP = 0
I L,PP = 0.5 I O
I L,PP = 0.75 I O
0
0 0.2 0.4 0.6 0.8 1.0
DUTY CYCLE (V O/ V IN )
FIGURE 28. NORMALIZED INPUT-CAPACITOR RMS
CURRENT vs DUTY CYCLE FOR SINGLE-PHASE
CONVERTER
placement. Critical small signal components to place close
to the controller include the ISEN resistors, R T resistor,
feedback resistor, and compensation components.
Bypass capacitors for the ISL6307A and ISL66XX driver
bias supplies must be placed next to their respective pins.
Trace parasitic impedances will reduce their effectiveness.
Plane Allocation and Routing
Dedicate one solid layer, usually a middle layer, for a ground
plane. Make all critical component ground connections with
vias to this plane. Dedicate one additional layer for power
planes; breaking the plane up into smaller islands of
common voltage. Use the remaining layers for signal wiring.
Route phase planes of copper filled polygons on the top and
bottom once the switching component placement is set. Size
the trace width between the driver gate pins and the
MOSFET gates to carry 4A of current. When routing
components in the switching path, use short wide traces to
reduce the associated parasitic impedances.
Layout Considerations
The following layout strategies are intended to minimize the
impact of board parasitic impedances on converter
performance and to optimize the heat-dissipating capabilities
of the printed-circuit board. These sections highlight some
important practices which should not be overlooked during the
layout process.
Component Placement
Within the allotted implementation area, orient the switching
components first. The switching components are the most
critical because they carry large amounts of energy and tend
to generate high levels of noise. Switching component
placement should take into account power dissipation. Align
the output inductors and MOSFETs such that spaces
between the components are minimized while creating the
PHASE plane. Place the Intersil MOSFET driver IC close to
the MOSFETs they control, to reduce the parasitic
impedances due to trace length between critical driver input
and output signals. If possible, duplicate the same
placement of these components for each phase.
Next, place the input and output capacitors. Position one
high-frequency ceramic input capacitor next to each upper
MOSFET drain. Place the bulk input capacitors as close to
the upper MOSFET drains as dictated by the component
size and dimensions. Long distances between input
capacitors and MOSFET drains result in too much trace
inductance and a reduction in capacitor performance. Locate
the output capacitors between the inductors and the load,
while keeping them in close proximity to the microprocessor
socket.
The ISL6307A can be placed off to one side or centered
relative to the individual phase switching components.
Routing of sense lines and PWM signals will guide final
32
FN9236.0
February 6, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6307BIRZ | IC REG CTRLR BUCK PWM VM 48-QFN |
| ISL6307IRZ | IC REG CTRLR BUCK PWM VM 48-QFN |
| ISL6308AIRZ | IC CTRLR PWM BUCK 3PHASE 40-QFN |
| ISL6308IRZ | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| ISL6310IRZ | IC CTRLR PWM 2PHASE BUCK 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6307AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307BCRZ | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR COM RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| ISL6307BCRZ-T | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR COM TAPE AND RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| ISL6307BIRZ | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR INDUSTRIAL RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| ISL6307BIRZ-T | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR INDUSTRIAL RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。