参数资料
| 型号： | ISL6310IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 25/27页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 2PHASE BUCK 32-QFN |
| 标准包装： | 6,000 |
| 应用： | 控制器，DDR |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 2.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页
ISL6310
layout of the critical components, and short, wide circuit
traces minimize the magnitude of voltage spikes.
There are two sets of critical components in a DC/DC
converter using a ISL6310 controller. The power-
components are the most critical because they switch large
amounts of energy. Next are small signal components that
connect to sensitive nodes or supply critical bypassing
current and signal coupling.
It is important to have a symmetrical layout, preferably with
the controller equidistantly located from the two power trains it
controls. Equally important are the gate drive lines (UGATE,
LGATE, PHASE): since they drive the power train MOSFETs
using short, high current pulses, it is important to size them as
large and as short as possible to reduce their overall
impedance and inductance. Extra care should be given to the
LGATE traces in particular since keeping the impedance and
inductance of these traces helps to significantly reduce the
possibility of shoot-through. Equidistant placement of the
controller to the two power trains also helps keeping these
traces equally short (equal impedances, resulting in similar
driving of both sets of MOSFETs).
The power components should be placed first. Locate the input
capacitors close to the power switches. Minimize the length of
the connections between the input capacitors, C IN , and the
power switches. Locate the output inductors and output
capacitors between the MOSFETs and the load. Locate the
high-frequency decoupling capacitors (ceramic) as close as
practicable to the decoupling target, making use of the shortest
connection paths to any internal planes, such as vias to GND
immediately next, or even onto the capacitor solder pad.
25
The critical small components include the bypass capacitors
for VCC and PVCC. Locate the bypass capacitors, CBP,
close to the device. It is especially important to locate the
components associated with the feedback circuit close to
their respective controller pins, since they belong to a high
impedance circuit loop, sensitive to EMI pick-up. It is also
important to place current sense components close to their
respective pins on the ISL6310, including the RISEN
resistors, RS, RCOMP, CCOMP. For proper current sharing
route two separate symmetrical as possible traces from the
corresponding phase node for each RISEN.
A multi-layer printed circuit board is recommended. Figure 27
shows the connections of the critical components for the
converter. Note that capacitors C xxIN and C xxOUT could each
represent numerous physical capacitors. Dedicate one solid
layer, usually the one underneath the component side of the
board, for a ground plane and make all critical component
ground connections with vias to this layer. Dedicate another
solid layer as a power plane and break this plane into smaller
islands of common voltage levels. Keep the metal runs from
the PHASE terminal to inductor L OUT short. The power plane
should support the input power and output power nodes. Use
copper filled polygons on the top and bottom circuit layers for
the phase nodes. Use the remaining printed circuit layers for
small signal wiring. The wiring traces from the IC to the
MOSFETs’ gates and sources should be sized to carry at least
one ampere of current (0.02” to 0.05”).
FN9209.4
August 7, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ECA49DTAS | CONN EDGECARD 98POS R/A .125 SLD |
| 2510-08K | INDUCTOR RF .22UH UNSHIELDED SMD |
| ISL6310CRZ-T | IC CTRLR PWM 2PHASE BUCK 32-QFN |
| ECA50DTAN | CONN EDGECARD 100PS R/A .125 SLD |
| 2510-06K | INDUCTOR RF .18UH UNSHIELDED SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6312ACRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6312ACRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6312AIRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6312AIRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6312CRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。