- 您现在的位置：买卖IC网 > PDF目录15164 > ISL6326BCRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL6326BCRZ-T |
| 厂商： | Intersil |
| 文件页数： | 21/30页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 4,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 275kHz |
| 占空比： | 25% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
ISL6326B
MOSFETs to turn on. The ISL6326B will continue to protect
the load in this fashion as long as the overvoltage condition
occurs.
Once an overvoltage condition is detected, normal PWM
operation ceases until the ISL6326B is reset. Cycling the
voltage on EN_PWR, EN_VTT or VCC below the POR-
falling threshold will reset the controller. Cycling the VID
codes will not reset the controller.
VR_RDY
UV
50%
At the beginning of overcurrent shutdown, the controller
places all PWM signals in a high-impedance state within
20ns, commanding the Intersil MOSFET driver ICs to turn off
both upper and lower MOSFETs. The system remains in this
state a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft-
start. If the fault remains, the trip-retry cycles will continue
indefinitely (as shown in Figure 10) until either controller is
disabled or the fault is cleared. Note that the energy
delivered during trip-retry cycling is much less than during
full-load operation, so there is no thermal hazard during this
kind of operation.
OUTPUT CURRENT
DAC
SOFT-START, FAULT
AND CONTROL LOGIC
-
OC
+
85μA
I AVG
0A
VDIFF
+
-
OV
-
OC
+
2.0V
IOUT
OUTPUT VOLTAGE
VID + 0.175V
0V
2ms/DIV
FIGURE 9. VR_RDY AND PROTECTION CIRCUITRY
Overcurrent Protection
ISL6326B has two levels of overcurrent protection. Each
phase is protected from a sustained overcurrent condition by
limiting its peak current, while the combined phase currents
are protected on an instantaneous basis.
In instantaneous protection mode, ISL6326B utilizes the
sensed average current I AVG to detect an overcurrent
condition. See the Channel-Current Balance section for
more detail on how the average current is measured. The
average current is continually compared with a constant
85μA reference current, as shown in Figure 9. Once the
average current exceeds the reference current, a
comparator triggers the converter to shutdown.
The current out of IOUT pin is equal to the sensed average
current I AVG . With a resistor from IOUT to GND, the voltage
at IOUT will be proportional to the sensed average current
and the resistor value. ISL6326B continuously monitors the
voltage at IOUT pin. If the voltage at IOUT pin is higher than
2V, a comparator triggers the overcurrent shutdown. By
increasing the resistor between IOUT and GND, the
overcurrent protection threshold can be adjusted to be less
than 100μA. For example, the overcurrent threshold for the
sensed average current I AVG can be set to 80μA by using a
25k Ω resistor from IOUT to GND.
21
FIGURE 10. OVERCURRENT BEHAVIOR IN HICCUP MODE.
F SW = 500kHz
For the individual channel overcurrent protection, the
ISL6326B continuously compares the sensed current signal
of each channel with the 120μA reference current. If one
channel current exceeds the reference current, ISL6326B
will pull PWM signal of this channel to low for the rest of the
switching cycle. This PWM signal can be turned on next
cycle if the sensed channel current is less than the 120μA
reference current. The peak current limit of individual
channel will not trigger the converter to shutdown.
Thermal Monitoring (VR_HOT/VR_FAN)
There are two thermal signals to indicate the temperature
status of the voltage regulator: VR_HOT and VR_FAN. Both
VR_FAN and VR_HOT pins are open-drain outputs, and
external pull-up resistors are required. Those signals are
valid only after the controller is enabled.
The VR_FAN signal indicates that the temperature of the
voltage regulator is high and more cooling airflow is needed.
The VR_HOT signal can be used to inform the system that
the temperature of the voltage regulator is too high and the
CPU should reduce its power consumption. The VR_HOT
signal may be tied to the CPU’s PROC_HOT signal.
FN9286.0
April 21, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| H2BBG-10102-G4-ND | JUMPER-H1501TR/A2015G/H1501TR 2" |
| ISL9506HRZ-T | IC REG CTRLR BUCK PWM 40-QFN |
| VE-J51-EY-F4 | CONVERTER MOD DC/DC 12V 50W |
| RGM08DTAS-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| H2BBG-10102-B4-ND | JUMPER-H1501TR/A2015B/H1501TR 2" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6326BIRZ | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR IND RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326BIRZ-T | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR IND RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326CRZ | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR COM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326CRZ-T | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR COM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326CRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6326CRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。