参数资料
| 型号： | ISL6334BIRZ-T |
| 厂商： | Intersil |
| 文件页数： | 27/30页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM SYNC BUCK 40-QFN |
| 标准包装： | 4,000 |
| 应用： | 控制器，Intel VR11.1 |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页
ISL6334B, ISL6334C
The feedback resistor, R FB , has already been chosen as
Select a target bandwidth for the compensated system, f 0 .
The target bandwidth must be large enough to assure
adequate transient performance, but smaller than 1/3 of the
per-channel switching frequency. The values of the
compensation components depend on the relationships of f 0
to the L-C pole frequency and the ESR zero frequency. For
each of the three cases which follow, there is a separate set
of equations for the compensation components.
Output Filter Design
The output inductors and the output capacitor bank together
to form a low-pass filter responsible for smoothing the
pulsating voltage at the phase nodes. The output filter also
must provide the transient energy until the regulator can
respond. Because it has a low bandwidth compared to the
switching frequency, the output filter necessarily limits the
system transient response. The output capacitor must
supply or sink load current while the current in the output
inductors increases or decreases to meet the demand.
------------------- > f 0
R C = R FB --------------------------------------
0.75V
2 π V PP R FB f 0
------------------- ≤ f 0 < ------------------------------
Case 1:
Case 2:
1
2 π LC
2 π f 0 V P-P LC
IN
0.75V IN
C C = ------------------------------------
1 1
2 π LC 2 π C ( ESR )
In high-speed converters, the output capacitor bank is usually
the most costly (and often the largest) part of the circuit.
Output filter design begins with minimizing the cost of this part
of the circuit. The critical load parameters in choosing the
output capacitors are the maximum size of the load step, Δ I;
the load-current slew rate, di/dt; and the maximum allowable
output-voltage deviation under transient loading, Δ V MAX .
Capacitors are characterized according to their capacitance,
ESR, and ESL (equivalent series inductance).
R C = R FB ----------------------------------------------
0.75 V
C C = -------------------------------------------------------------
PP R FB LC
( 2 π ) 2 f 2 V
V P-P ( 2 π ) 2 f 02 LC
IN
0.75V IN
0
(EQ. 34)
At the beginning of the load transient, the output capacitors
supply all of the transient current. The output voltage will initially
deviate by an amount approximated by the voltage drop across
the ESL. As the load current increases, the voltage drop across
the ESR increases linearly until the load current reaches its final
f 0 > ------------------------------
0.75 V IN ( ESR )
Case 3:
1
2 π C ( ESR )
2 π f 0 V P-P L
R C = R FB ------------------------------------------
value. The capacitors selected must have sufficiently low ESL
and ESR so that the total output-voltage deviation is less than
the allowable maximum. Neglecting the contribution of inductor
current and regulator response, the output voltage initially
deviates by an amount, as shown in Equation 35:
2 π V PP R FB f 0 L
Δ V ≈ ( ESL ) ----- + ( ESR ) Δ I
0.75V IN ( ESR ) C
C C = -------------------------------------------------
di
dt
(EQ. 35)
The filter capacitor must have sufficiently low ESL and ESR
In Equation 34, L is the per-channel filter inductance divided
by the number of active channels; C is the sum total of all
output capacitors; ESR is the equivalent-series resistance of
the bulk output-filter capacitance; and V PP is the sawtooth
amplitude described in the “Electrical Specifications” table
The optional capacitor C 2 , is sometimes needed to bypass
noise away from the PWM comparator. Keep a position
available for C 2 , and be prepared to install a high-frequency
capacitor of between 10pF and 100pF in case any
leading-edge jitter problem is noted.
Once selected, the compensation values in Equation 34
assure a stable converter with reasonable transient
performance. In most cases, transient performance can be
improved by making adjustments to R C . Slowly increase the
value of R C while observing the transient performance on an
oscilloscope until no further improvement is noted. Normally,
so that Δ V < Δ V MAX .
Most capacitor solutions rely on a mixture of high-frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors also creates the majority of
the output-voltage ripple. As the bulk capacitors sink and
source the inductor AC ripple current (see “Interleaving” on
bulk-capacitor ESR equal to I C,PP (ESR). Thus, once the
output capacitors are selected, the maximum allowable
ripple voltage, V PP(MAX) , determines the lower limit on the
inductance, as shown in Equation 36.
– N V OUT ? ? V OUT
? V
L ≥ ESR ? ----------------------------------------------------------------
C C will not need adjustment. Keep the value of C C from
Equation 34 unless some performance issue is noted.
27
? IN ?
f S ? V IN ? V P-P ( MAX )
(EQ. 36)
FN6689.2
August 31, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6334CRZ | IC CTRLR PWM 4PHASE BUCK 40-QFN |
| ISL6334DIRZ | IC CTRLR PWM 4PHASE VR11.1 40QFN |
| ISL6336BCRZ | IC CTRLR PWM SYNC BUCK 48-QFN |
| ISL6336IRZ | IC CTRLR PWM 6PHASE BUCK 48-QFN |
| ISL6341CIRZ | IC REG CTRLR BUCK PWM VM 10-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6334CCRZ | 功能描述:IC CTRLR PWM SYNC BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334CCRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334CIRZ | 功能描述:IC CTRLR PWM SYNC BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6334CIRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334CRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。