- 您现在的位置：买卖IC网 > PDF目录16598 > ISL6441IR-T (Intersil)IC CTRLR PWM DUAL 1.4MHZ 28-QFN PDF资料下载
参数资料
| 型号： | ISL6441IR-T |
| 厂商： | Intersil |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM DUAL 1.4MHZ 28-QFN |
| 标准包装： | 6,000 |
| 应用： | 电源 |
| 电流 - 电源： | 2mA |
| 电源电压： | 5.6 V ~ 24 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
ISL6441
is detected for 2 consecutive clock cycles then the IC enters
a hiccup mode by turning off the gate drivers and entering
into soft-start. The IC will cycle 2x through soft-start before
trying to restart. The IC will continue to cycle through
soft-start until the overcurrent condition is removed.
Figure 17 shows this behavior.
.
Implementing Synchronization
The SYNC pin may be used to synchronize two or more
controllers. When the SYNC pins of two controllers are
connected together, one controller becomes the master and
the other controller synchronizes to the master. A pull-down
resistor is required and must be sized to provide a low
enough time constant to pass the SYNC pulse. Connect this
pin to VCC_5V if not used. Figure 18 shows the SYNC pin
waveform operating at 4x the switching frequency.
V OUT2 2V/DIV
SYNC 1V/DIV
I L 2V/DIV
PHASE2 10V/DIV
FIGURE 16. OVERCURRENT TRIP WAVEFORMS
V OUT2 2V/DIV
I OUT2 2V/DIV
SS2 2V/DIV
FIGURE 17. OVERCURRENT CONTINUOUS HICCUP MODE
WAVEFORMS
Because of the nature of this current sensing technique, and
to accommodate a wide range of r DS(ON) variations, the
value of the overcurrent threshold should represent an
overload current about 150% to 180% of the maximum
operating current. If more accurate current protection is
desired, place a current sense resistor in series with the
lower MOSFET source.
Over-Temperature Protection
The IC incorporates an over-temperature protection circuit
FIGURE 18. SYNC WAVEFORM
Feedback Loop Compensation
To reduce the number of external components and to
simplify the process of determining compensation
components, both PWM controllers have internally
compensated error amplifiers. To make internal
compensation possible several design measures were
taken.
First, the ramp signal applied to the PWM comparator is
proportional to the input voltage provided via the VIN pin.
This keeps the modulator gain constant with variation in the
input voltage. Second, the load current proportional signal is
derived from the voltage drop across the lower MOSFET
during the PWM time interval and is subtracted from the
amplified error signal on the comparator input. This creates
an internal current control loop. The resistor connected to
the ISEN pin sets the gain in the current feedback loop. The
following expression estimates the required value of the
current sense resistor depending on the maximum operating
load current and the value of the MOSFET’s r DS(ON) .
( I MAX ) ( r DS ( ON ) )
that shuts the IC down when a die temperature of +150°C
is reached. Normal operation resumes when the die
temperatures drops below +130°C through the initiation of
32 μ A
R CS ≥ -----------------------------------------------
(EQ. 6)
a full soft-start cycle.
13
Choosing R CS to provide 32μA of current to the current
sample and hold circuitry is recommended but can operate
down to 2μA up to 100μA.
FN9197.3
May 26, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| RCC05DRYS-S734 | CONN EDGECARD 10POS DIP .100 SLD |
| GSC12DRXH-S734 | CONN EDGECARD 24POS DIP .100 SLD |
| EMC12DREI-S13 | CONN EDGECARD 24POS .100 EXTEND |
| ISL6218CV-T | IC CTRLR INTEL PENT M 38-TSSOP |
| RCM15DCBD | CONN EDGECARD 30POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6441IR-TK | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
| ISL6441IRZS2695 | 制造商:Intersil Corporation 功能描述: |
| ISL6441IRZ-T | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IRZ-TK | 功能描述:IC CTRLR PWM 1.4MHZ DUAL 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。