- 您现在的位置：买卖IC网 > PDF目录16598 > ISL6441IR-T (Intersil)IC CTRLR PWM DUAL 1.4MHZ 28-QFN PDF资料下载
参数资料
| 型号： | ISL6441IR-T |
| 厂商： | Intersil |
| 文件页数： | 16/18页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM DUAL 1.4MHZ 28-QFN |
| 标准包装： | 6,000 |
| 应用： | 电源 |
| 电流 - 电源： | 2mA |
| 电源电压： | 5.6 V ~ 24 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
ISL6441
The power dissipation includes two loss components;
conduction loss and switching loss. These losses are
distributed between the upper and lower MOSFETs
according to duty cycle (see Equations 10 and 11). The
conduction losses are the main component of power
dissipation for the lower MOSFETs. Only the upper MOSFET
has significant switching losses, since the lower device turns
on and off into near zero voltage. Equations 10 and 11
assume linear voltage-current transitions and do not model
power loss due to the reverse-recovery of the lower
MOSFET’s body diode.
is the input voltage, V O is output voltage, and DV OUT is the
drop in output voltage allowed during the load transient.
High frequency capacitors initially supply the transient
current and slow the load rate-of-change seen by the bulk
capacitors. The bulk filter capacitor values are generally
determined by the ESR (Equivalent Series Resistance) and
voltage rating requirements as well as actual capacitance
requirements.
The output voltage ripple is due to the inductor ripple current
and the ESR of the output capacitors as defined by
( I O ) ( r DS ( ON ) ) ( V OUT )
( I O ) ( V IN ) ( t SW ) ( F SW )
P UPPER = --------------------------------------------------------------- + ------------------------------------------------------------
V IN
(EQ. 10)
2
2
Equation 13.
V RIPPLE = Δ I L ( ESR )
(EQ. 13)
( I O ) ( r DS ( ON ) ) ( V IN – V OUT )
P LOWER = -------------------------------------------------------------------------------
2
V IN
(EQ. 11)
where, I L is calculated in the “Output Inductor Selection” on
page 17.
High frequency decoupling capacitors should be placed as
A large gate-charge increases the switching time, t SW ,
which increases the upper MOSFET switching losses.
Ensure that both MOSFETs are within their maximum
junction temperature at high ambient temperature by
calculating the temperature rise according to package
thermal-resistance specifications.
Output Capacitor Selection
The output capacitors for each output have unique
requirements. In general, the output capacitors should be
selected to meet the dynamic regulation requirements
including ripple voltage and load transients. Selection of
output capacitors is also dependent on the output inductor,
so some inductor analysis is required to select the output
capacitors.
One of the parameters limiting the converter ’s response to a
load transient is the time required for the inductor current to
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load
circuitry for specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications at 1.4MHz for the bulk
capacitors. In most cases, multiple small-case electrolytic
capacitors perform better than a single large-case capacitor.
The stability requirement on the selection of the output
capacitor is that the ‘ESR zero’, f Z , be between 2kHz and
50kHz. This range is set by an internal, single compensation
zero at 10kHz. The ESR zero can be a factor of five on either
side of the internal zero and still contribute to increased
phase margin of the control loop. Therefore, see
Equation 14.
C OUT = ------------------------------------
slew to its new level. The ISL6441 will provide either 0% or
71% duty cycle in response to a load transient.
The response time is the time interval required to slew the
1
2 π ( ESR ) ( f Z )
(EQ. 14)
inductor current from an initial current value to the load
current level. During this interval the difference between the
inductor current and the transient current level must be
supplied by the output capacitor(s). Minimizing the response
time can minimize the output capacitance required. Also, if
the load transient rise time is slower than the inductor
response time, as in a hard drive or CD drive, it reduces the
requirement on the output capacitor.
The maximum capacitor value required to provide the full,
rising step, transient load current during the response time of
the inductor is shown in Equation 12:
In conclusion, the output capacitors must meet three criteria:
1. They must have sufficient bulk capacitance to sustain the
output voltage during a load transient while the output
inductor current is slewing to the value of the load
transient,
2. The ESR must be sufficiently low to meet the desired
output voltage ripple due to the output inductor current,
and
3. The ESR zero should be placed in a rather large range,
to provide additional phase margin.
The recommended output capacitor value for the ISL6441 is
( L O ) ( I TRAN )
2 ( V IN – V O ) ( DV OUT )
2
C OUT = -----------------------------------------------------------
(EQ. 12)
between 150μF to 680μF, to meet stability criteria with
external compensation. Use of low ESR ceramic capacitors
is possible but would take more rigorous loop analysis to
where, C OUT is the output capacitor(s) required, L O is the
output inductor, I TRAN is the transient load current step, V IN
16
ensure stability.
FN9197.3
May 26, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| RCC05DRYS-S734 | CONN EDGECARD 10POS DIP .100 SLD |
| GSC12DRXH-S734 | CONN EDGECARD 24POS DIP .100 SLD |
| EMC12DREI-S13 | CONN EDGECARD 24POS .100 EXTEND |
| ISL6218CV-T | IC CTRLR INTEL PENT M 38-TSSOP |
| RCM15DCBD | CONN EDGECARD 30POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6441IR-TK | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
| ISL6441IRZS2695 | 制造商:Intersil Corporation 功能描述: |
| ISL6441IRZ-T | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IRZ-TK | 功能描述:IC CTRLR PWM 1.4MHZ DUAL 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。