- 您现在的位置：买卖IC网 > Datasheet目录334 > ISL6442EVAL1Z (Intersil)EVAL BOARD FOR ISL6442 Datasheet资料下载
参数资料
| 型号： | ISL6442EVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR ISL6442 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 3，非隔离 |
| 输出电压： | 1.8V，3.3V，5V |
| 电流 - 输出： | 3A，3A，300mA |
| 输入电压： | 6V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1.4MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL6442 |
ISL6442
UVP - (Function independent for both PWM). If the voltage
on the FB pin falls to 82% (typical) of the reference voltage
Δ V OUT = Δ I x ESR
(EQ. 7)
for 8 consecutive PWM cycles, then the circuit enters into
soft-start hiccup mode. This mode is identical to the
overcurrent hiccup mode. The UVP comparator is separate
from the one sensing for PGOOD, which should have
already detected a problem, before the UVP trips.
OVP - (Function independent for both PWM). If voltage on
FB pin rises to 116% (typical) of the reference voltage, the
lower gate driver is turned on continuously (with diode
emulation enabled). If SS_DN (internal soft-start done
signal) is true (not in soft-start) and the overvoltage condition
continues for 32 consecutive PWM cycles, then that output
is latched off with the gate drivers three-stated. The
capacitor on the SS/EN pin will not be discharged. The
switcher will restart when the SS/EN pin is externally driven
below 1V, or if power is recycled to the chip, or when the
voltage on the FB pin falls to the 82% (typical) undervoltage
threshold - after 8 clock cycles the chip will enter soft-start
hiccup mode. The hiccup mode is identical to the
overcurrent hiccup mode. The OVP comparator is separate
from the one sensing for PGOOD, which should have
already detected a problem, before the OVP trips.
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance value reduces
the converter ’s response time to a load transient (and
usually increases the DCR of the inductor, which decreases
the efficiency). Increasing the switching frequency (F SW ) for
a given inductor also reduces the ripple current and voltage.
One of the parameters limiting the converter ’s response to a
load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6442 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval, the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
t RISE = ---------------------------------------
t FALL = ---------------------------------------
Application Guidelines
PWM Controller
DISCUSSION
The PWM must be compensated such that it achieves the
desired transient performance goals, stability, and DC
L OUT × I TRAN
V IN – V OUT
L OUT × I TRAN
V OUT
(EQ. 8)
(EQ. 9)
regulation requirements.
The first parameter that needs to be chosen is the switching
frequency, F SW . This decision is based on the overall size
constraints and the frequency plan of the end equipment.
Smaller space requires higher frequency. This allows the
output inductor, input capacitor bank, and output capacitor
bank to be reduced in size and/or value. The power supply
must be designed such that the frequency and its distribution
over component tolerance, time and temperature causes
minimal interference in RF stages, IF stages, PLL loops,
mixers, etc.
INDUCTOR SELECTION
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter ’s response
time to the load transient. The inductor value determines the
converter ’s ripple current, and the ripple voltage is a function
of the ripple current. The ripple current and voltage are
approximated by the following equations, where ESR is the
output capacitance ESR value.
where: I TRAN is the transient load current step, t RISE is the
response time to the application of load, and t FALL is the
response time to the removal of load. With a +5V input
source, the worst case response time can be either at the
application or removal of load and dependent upon the
output voltage setting. Be sure to check both of these
equations at the minimum and maximum output levels for
the worst case response time.
Finally, check that the inductor I sat rating is sufficiently above
the maximum output current (DC load plus ripple current).
OUTPUT CAPACITOR SELECTION
An output capacitor is required to filter the output and supply
the load transient current. The filtering requirements are a
function of the switching frequency and the ripple current.
The load transient requirements are a function of the slew
rate (di/dt) and the magnitude of the transient load current.
These requirements are generally met with a mix of
capacitors and careful layout.
Modern microprocessors produce transient load rates above
V IN - V OUT V OUT
F SW ? L
Δ I = -------------------------------- ? ----------------
V IN
11
(EQ. 6)
1A/ns. High frequency capacitors initially supply the transient
and slow the current load rate seen by the bulk capacitors.
The bulk filter capacitor values are generally determined by
the ESR (effective series resistance) and voltage rating
requirements rather than actual capacitance requirements.
FN9204.2
October 31, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6445EVAL3Z | EVALUATION BOARD FOR ISL6445 |
| ISL6524EVAL1 | EVALUATION BOARD VRM8.5 ISL6524 |
| ISL6527EVAL1 | EVALUATION BOARD SOIC ISL6527 |
| ISL6532AEVAL1 | EVALUATION BOARD 1 ISL6532A |
| ISL6553EVAL1 | EVALUATION BOARD ISL6553 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6442IA | 功能描述:IC REG TRPL BCK/LINEAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6442IA-TK | 功能描述:IC REG TRPL BCK/LINEAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6442IAZ | 功能描述:IC REG TRPL BCK/LINEAR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6442IAZ-TK | 功能描述:IC REG TRPL BCK/LINEAR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6442IAZ-TKS2715 | 制造商:Intersil Corporation 功能描述:BROADCOM, ISL6442IAZ-TK BUSINESS TRACKING REQUIREMENTS, SOLD - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。