- 您现在的位置：买卖IC网 > PDF目录20613 > ISL6442IAZ (Intersil)IC REG TRPL BCK/LINEAR 24QSOP PDF资料下载
参数资料
| 型号： | ISL6442IAZ |
| 厂商： | Intersil |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BCK/LINEAR 24QSOP |
| 标准包装： | 1,000 |
| 拓扑： | 降压（降压）同步（2），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 300kHz ~ 2.55MHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | * |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
ISL6442
Pin Descriptions
BOOT1, 2 (Pins 23, 14) - These pins power the upper
MOSFET drivers of each PWM converter. The anode of the
each internal bootstrap diode is connected to the VCC pin.
The cathode of the bootstrap diode is connected to this pin,
which should also connect to the bootstrap capacitor.
UGATE1, 2 (Pins 22, 15) - These pins provide the gate
drive for upper MOSFETs, bootstrapped from the VCC pin.
PHASE1, 2 (Pins 21, 16) - These are the junction points of
the upper MOSFET sources, output filter inductor and lower
MOSFET drains. Connect these pins accordingly to the
respective converter.
LGATE1, 2 (Pins 20, 17) - These are the outputs of the lower
N-Channel MOSFET drivers, sourced from the VCC pin.
PGND (Pin 18) - This pin provides the power ground
connection for the lower gate drivers. This pin should be
connected to the source of the lower MOSFET for PWM1
and PWM2 and the negative terminals of the external input
capacitors.
FB1, 2 (Pins 4, 9) - These pins are connected to the feedback
resistor divider and provide the voltage feedback signals for the
respective controller. They set the output voltage of the
converter. In addition, the PGOOD circuit and OVP circuit use
these inputs to monitor the output voltage status.
COMP1, 2 (Pins 3, 10) - These pins are the error amplifier
outputs for the respective PWM. They are used, along with the
FB pins, as the compensation point for the PWM error amplifier.
PGOOD (Pin 13) - This is an open drain logic output used to
indicate the status of the output voltages. This pin is pulled low
when either of the two PWM outputs is not within 10% of the
respective nominal voltage or when the linear output drops
below 75% of its nominal voltage. To maintain the PGOOD
function if the linear output is not used, connect LCFB to VCC.
SGND (Pin 6) - This is the signal ground, common to both
controllers, and must be routed separately from the high
current grounds (PGND). All voltage levels are measured
VCC (Pin 19) - This pin supplies the bias for the regulators,
powers the low side gate drivers and external boot circuitry
for high side gate drivers. The IC may be powered directly
from a single 5V (±10%) supply at this pin; when used as a
5V supply input, this pin must be externally connected to
VIN. When VIN > 5.5, VCC is the output of the internal 5V
linear regulator output. The VCC pin must always be
decoupled to power ground with a minimum of 1μF ceramic
capacitor, placed very close to the pin.
RT (Pin 5) - This is the operating frequency adjustment pin.
By placing a resistor from this pin to SGND, the oscillator
frequency can be programmed from 300kHz to 2.5MHz.
SS1/EN1, 2 (Pins 2, 11) - These pins provide
enable/disable and soft-start function for their respective
controllers. The output is held off when the pin is pulled to
the ground. When the chip is enabled, the regulated 30μA
pull-up current source charges the capacitor connected from
the pin to ground. The output voltage of the converter follows
the ramping voltage on the SS/EN pin. Note that if either
input is held low during power-up, neither channel will start a
soft-start ramp until both are released. Once both outputs
are running, then either one can be separately disabled and
then enabled. But if both are disabled, that requires that both
are released before either starts up. See Soft-Start and
Voltage Tracking section for more details.
LCFB (Pin 8) - This pin is the feedback pin for the linear
controller. An external voltage divider network connected to
this pin sets the output voltage of the linear controller. If the
linear controller is not used, tie this pin to VCC.
LCDR (Pin 7) - Open drain output PNP Transistor Driver.
LCDR connects to the base of an external PNP pass
transistor to form a positive linear regulator.
OCSET1, 2 (Pins 1, 12) - These pins are the overcurrent set
points for the respective PWM controllers. Connect a resistor
(R OCSET ) from this pin to the drain of the upper MOSFET.
R OCSET , an internal 100μA current source, and the upper
MOSFET ON resistance r DS(ON) set the converter
overcurrent (OC) trip point according to Equation 1:
I OC = ---------------------------------------------------
with respect to this pin.
VIN (Pin 24) - This pin powers the controllers with an
internal linear regulator (if VIN > 5.5V) and must be closely
I OCSET ? R OCSET
r DS ( ON ) )
(EQ. 1)
decoupled to ground using a ceramic capacitor as close to
the VIN pin as possible. VIN is also the input voltage applied
to the upper FET of both converters.
TABLE 1. INPUT SUPPLY CONFIGURATION
I OC includes the DC load current, as well as the ripple
current. An overcurrent trip initiates hiccup mode.
Functional Description
Soft-Start and Voltage Tracking
INPUT
5.5V to 24V
5V ±10%
PIN CONFIGURATION
Connect the input supply to the VIN pin. The
VCC pin will provide a 5V output from the
internal voltage regulator.
Connect the input supply to the VCC pin.
7
After the VCC pin exceeds its rising POR trip point (nominal
4.4V), the chip operation begins. While the voltage on both
SS1/EN1 and SS2/EN2 is below 1.0V, the internal switch
between SS1/EN1 and SS2/EN2 is turned on so that the
voltage across these two pins is the same. If either pin is
held low externally, nothing happens until both pins are
FN9204.2
October 31, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6442IAZ-TK | IC REG TRPL BCK/LINEAR 24QSOP |
| AGM28DTMH | CONN EDGECARD 56POS R/A .156 SLD |
| ECC28DCMS | CONN EDGECARD 56POS .100 WW |
| AGM28DTMD | CONN EDGECARD 56POS R/A .156 SLD |
| EMC65DREI-S13 | CONN EDGECARD 130POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6442IAZ-TK | 功能描述:IC REG TRPL BCK/LINEAR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6442IAZ-TKS2715 | 制造商:Intersil Corporation 功能描述:BROADCOM, ISL6442IAZ-TK BUSINESS TRACKING REQUIREMENTS, SOLD - Tape and Reel |
| ISL6443AEVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6443A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6443AIRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
| ISL6443AIRZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。