- 您现在的位置：买卖IC网 > PDF目录20679 > ISL6528CBZ-T (Intersil)IC REG DL BCK/LINEAR SYNC 8-SOIC PDF资料下载
参数资料
| 型号： | ISL6528CBZ-T |
| 厂商： | Intersil |
| 文件页数： | 9/13页 |
| 文件大小： | 361K |
| 描述： | IC REG DL BCK/LINEAR SYNC 8-SOIC |
| 标准包装： | 1 |
| 拓扑： | 降压（降压）同步（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 2 |
| 频率 - 开关： | 600kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | * |
| 包装： | 标准包装 |
| 产品目录页面： | 1243 (CN2011-ZH PDF) |
| 其它名称： | ISL6528CBZ-TDKR |
9
FN9038.4
March 9, 2006
by placing them nearby. Position both the ceramic and bulk
input capacitors as close to the upper MOSFET drain as
possible. Position the output inductor and output capacitors
between the upper MOSFET and lower diode and the load.
The critical small signal components include any bypass
capacitors, feedback components, and compensation
components. Position the bypass capacitor, C
BP
, close to
the VCC pin with a via directly to the ground plane. Place the
PWM converter compensation components close to the FB
and COMP pins. The feedback resistors for both regulators
should also be located as close as possible to the relevant
FB pin with vias tied straight to the ground plane as required.
Component Selection Guidelines
Output Capacitor Selection
Output capacitors are required to filter the output and supply
the load transient current. The filtering requirements are a
function of switching frequency and output current ripple.
The load transient requirements are a function of the
transient load current slew rate (di/dt) and magnitude. These
requirements are generally met with a mix of capacitors and
careful layout.
PWM REGULATOR OUTPUT CAPACITORS
Modern digital ICs can produce high transient load slew
rates. High frequency capacitors initially supply the transient
current and slow the load rate-of-change seen by the bulk
capacitors. The bulk filter capacitor selection is generally
determined by the effective series resistance (ESR) and
voltage rating requirements rather than actual capacitance
requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements.
Specialized low-ESR capacitors intended for switching-
regulator applications are recommended for the bulk
capacitors. The bulk capacitors ESR determines the output
ripple voltage and the initial voltage drop following a high
slew-rate transient edge. Aluminum electrolytic, tantalum,
and special polymer capacitor ESR values are related to the
case size with lower ESR available in larger case sizes.
However, the equivalent series inductance (ESL) of these
capacitors increases with case size and can reduce the
usefulness of the capacitor to high slew-rate transient
loading. Unfortunately, ESL is not a specified parameter.
Work with your capacitor supplier and measure the
capacitors impedance with frequency to select a suitable
component. In most cases, multiple electrolytic capacitors of
small case size perform better than a single large case
capacitor.
LINEAR REGULATOR OUTPUT CAPACITORS
The output capacitors for the linear regulator provide
dynamic load current. The linear controller uses dominant
pole compensation integrated into the error amplifier and is
relatively insensitive to output capacitor selection. Output
capacitors should be selected for transient load regulation.
PWM Output Inductor Selection
The PWM converter requires an output inductor. The output
inductor is selected to meet the output voltage ripple
requirements and sets the converter response time to a load
transient. The inductor value determines the converters
ripple current and the ripple voltage is also a function of the
ripple current. The ripple voltage and current are
approximated by the following equations:
Increasing the value of inductance reduces the output ripple
current and voltage ripple. However, increasing the
V
OUT1
+5 VCC
ISLAND ON POWER PLANE LAYER
ISLAND ON CIRCUIT PLANE LAYER
L
OUT
C
OUT1
C
IN
+3.3 V
IN
KEY
COMP
ISL6528
UGATE
R4
R
2
C
BP
FB
DRIVE2
GND
VCC
D1
FIGURE 7. PRINTED CIRCUIT BOARD POWER PLANES AND
ISLANDS
R1
Q2
V
OUT2
BOOT
FB2
C
2
VIA CONNECTION TO GROUND PLANE
C
OUT2
Q1
C
BOOT
+3.3 V
IN
R5
R6
PHASE
D2
R
3
C
3
C
1
I
V
IN
V
OUT
F
S
L
?/DIV>
--------------------------------
V
OUT
V
IN
----------------
?/DIV>
=
V
OUT
I
ESR
?/DIV>
=
(EQ. 11)
(EQ. 12)
ISL6528
相关PDF资料 |
PDF描述 |
|---|---|
| GBC13DCMS | CONN EDGECARD 26POS .100" WW |
| RSO-1215DZ/H2 | CONV DC/DC 1W 4.5-18V +/-15VOUT |
| T95S475M6R3HSAL | CAP TANT 4.7UF 6.3V 20% 1507 |
| TH3C106M016E1400 | CAP TANT 10UF 16V 20% 2312 |
| ECM06DTBT-S189 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6528CBZ-TS2698 | 功能描述:IC REG DL BCK/LINEAR SYNC 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6529ACB | 功能描述:IC REG DL BCK/LINEAR 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6529ACB-T | 功能描述:IC REG DL BCK/LINEAR 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6529ACR | 功能描述:IC REG DL BCK/LINEAR SYNC 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6529ACR-T | 功能描述:IC REG DL BCK/LINEAR SYNC 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
发布紧急采购，3分钟左右您将得到回复。