参数资料
| 型号： | ISL6539IA-T |
| 厂商： | Intersil |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR DDR DRAM, SDRAM 28QSOP |
| 标准包装： | 2,500 |
| 应用： | 控制器，DDR DRAM，SDRAM |
| 输入电压： | 3.3 V ~ 18 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 带卷 (TR) |
ISL6539
channel controller are disabled when the DDR pin is set
high. As the VTT channel tracks the VDDQ/2 voltage, the
soft-start function is not required, and the SOFT2 pin may be
left open, in the event both channels are enabled
simultaneously. However, if the VTT channel is enabled later
than the VDDQ, the SOFT2 pin must have a capacitor in
place to ensure soft-start. In case of overcurrent or
undervoltage caused by short circuit on VTT, the fault current
will propagate to the first channel and shut down the
converter.
1. the quiescent current, supporting the internal logic and
normal operation of the IC
2. the gate driver current for the lower MOSFETs
3. and the current going through the external diodes to the
bootstrap capacitor for upper MOSFET.
In order to reduce the noisy effect of the bootstrap capacitor
current to the IC, a small resistor, such as 10 Ω , can be used
with the decoupling cap to construct a low pass filter for the
IC, as shown in Figure 11.
TO BOOT
The VREF voltage will be present even if the VTT is
disabled.
5V
VCC
I SOURCING ( 140 Ω + R CS ) = I D r DS ( ON )
Channel Synchronization in DDR Applications
The presence of two PWM controllers on the same die
requires channel synchronization, to reduce inter-channel
interference that may cause the duty factor jitter and
increased output ripple.
The PWM controller is at greatest noise susceptibility when
an error signal on the input of the PWM comparator
approaches the decision-making point. False triggering may
occur, causing jitter and affecting the output regulation.
A common approach used to synchronize dual channel
converters is out-of-phase operation. Out-of-phase
operation reduces input current ripple and provides a
minimum interference for channels that control different
voltage levels.
When used in a DDR application with cascaded converters
(VTT generated from VDDQ), several methods of
synchronization are implemented in the ISL6539. When the
DDR pin is connected to GND for dual switcher applications,
the channels operate 180° out-of-phase. In the DDR mode,
when the DDR pin is connected to VCC, the channels
operate either with 0° phase shift, when the VIN pin is
connected to the GND, or with 90° phase shift if the VIN pin
is connected to a voltage higher than 4.2V.
The following table lists the different synchronization
schemes and their usage:
DDR PIN VIN PIN SYNCHRONIZATION
10 Ω
FIGURE 11. INPUT FILTERING FOR THE CHIP
The soft-start capacitor and the resistor divider setting the
output voltage is easy to select as discussed in the “Block
Selection of the Current Sense Resistor
The value of the current sense resistor determines the gain
of the current sensing circuit. It affects the current loop gain
and the overcurrent protection setpoint. The voltage drop on
the lower MOSFET is sensed within 400ns after the upper
MOSFET is turned off. The current sense pin has a 140 Ω
resistor in series with the external current sensing resistor.
The current sense pin can source up to a 260μA current
while sensing current on the lower MOSFET, in such a way
that the voltage drop on the current sensing path would
equal to the voltage on the MOSFET.
(EQ. 16)
I D can be assumed to be the inductor peak current. In a
worst case scenario, the high temperature r DS(ON) could
increase to 150% of the room temperature level. During
overload condition, the MOSFET drain current I D could be
130% higher than the normal inductor peak. If the inductor
has 30% peak-to-peak ripple, I D would equal to 115% of the
load current. The design should consider the above factors
so that the maximum I SOURCING will not saturate to 260μA
under worst case conditions. To be safe, I SOURCING should
be less than 100μA in normal operation at room
0
1
1
V IN pin >4.2V
V IN pin voltage <4.2V
V IN pin voltage >4.1V
180° out-of-phase
0° phase
90° phase shift
temperature. The formula in the earlier discussion assumes
a 75μA sourcing current. Users can tune the sourcing
current of the ISEN pin to meet the overcurrent protection
and the change the current loop gain. The lower the current
sensing resistor, the higher gain of the current loop, which
Application Information
Design Procedures
GENERAL
A ceramic decoupling capacitor should be used between the
VCC and GND pin of the chip. There are three major
currents drawn from the decoupling capacitor:
14
can damp the output LC filter more.
A higher current-sensing resistor will decrease the current
sense gain. If the phase node of the converter is very noisy
due to poor layout, the sensed current will be contaminated,
resulting in duty cycle jittering by the current loop. In such a
case, a bigger current sense resistor can be used to reduce
both real and noise current levels. This can help damp the
phase node waveform jittering.
FN9144.6
April 29, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6540AIRZA-T | IC REG CTRLR BUCK PWM VM 28-QFN |
| ISL65426HRZ | IC REG BUCK SYNC ADJ 6A DL 50QFN |
| ISL6545IBZ-T | IC REG CTRLR BUCK PWM VM 8-SOIC |
| ISL6548ACRZA-T | IC REG/CTLR ACPI DUAL DDR 28QFN |
| ISL6548CRZA | IC REG/CTRLR ACPI DUAL DDR 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6539IAZ | 功能描述:电流型 PWM 控制器 ISL6539 DL SWITCHER 15V INDUSTRIAL GRD RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6539IAZ-T | 功能描述:电流型 PWM 控制器 ISL6539 DL SWITCHER 15V INDUSTRIAL GRD RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6540ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL6540ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| ISL6540ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6540ACRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。