- 您现在的位置：买卖IC网 > PDF目录15063 > ISL6559CB (Intersil)IC REG CTRLR BUCK PWM VM 28-SOIC PDF资料下载
参数资料
| 型号： | ISL6559CB |
| 厂商： | Intersil |
| 文件页数： | 13/21页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 28-SOIC |
| 标准包装： | 26 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 4MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
ISL6559
Over-Voltage Protection
When the output of the differential amplifier (VDIFF) reaches
controller counts 2048 phase clock cycles. This is followed
by a soft-start attempt (see Soft-Start ).
2.2V, PGOOD immediately goes low indicating a fault. Two
protective actions are taken by the ISL6559 to protect the
microprocessor load.
OUTPUT CURRENT, 20A/DIV
First, all PWM outputs are commanded low. Directing the
Intersil drivers to turn on the lower MOSFETs; shunting the
output to ground preventing any further increase in output
voltage. The PWM outputs remain low until VDIFF falls to the
programmed DAC level at which time they go into a high-
impedance state. The Intersil drivers respond by turning off
both upper and lower MOSFETs. If the over-voltage
condition reoccurs, the ISL6559 will again command the
lower MOSFETs to turn on. The ISL6559 will continue to
protect the load in this fashion as long as the over-voltage
0A
OUTPUT VOLTAGE,
500mV/DIV
repeats.
0V
5ms/DIV
Second, the OVP pin pulls to VCC and can deliver 100mA
into the gate of either a MOSFET or SCR placed across the
input voltage (V IN ) and V OUT . Turning on the MOSFET or
SCR collapses the power rail and causes a fuse placed
further up stream to blow. The fuse must be sized such that
the MOSFET or SCR will not overheat before the fuse blows.
Once an over-voltage condition is detected, normal PWM
operation ceases and PGOOD remains low until the
ISL6559 is reset. Cycling the voltage on EN below 1.23V or
the bias to VCC below the POR-falling threshold will reset
the controller.
Over-Current Protection
The ISL6559 takes advantage of the proportionality between
the load current and the average current, I AVG , to detect an
over-current condition. See the Channel-Current Balance
section for more detail on how the average current is
created. The average current is continually compared with a
constant 90 μ A reference current. Once the average current
exceeds the reference current, the comparator triggers the
converter to shutdown. The POR circuit places all PWM
signals in a high-impedance state which commands the
drivers to turn off both upper and lower MOSFETs. PGOOD
pulls low and the system remains in this state while the
13
FIGURE 11. OVERCURRENT BEHAVIOR IN HICCUP MODE
During the soft-start interval, the over-current protection
circuitry remains active. As the output voltage ramps up, if an
over-current condition is detected, the ISL6559 immediately
places all PWM signals in a high-impedance state. The
ISL6559 repeats the 2048-cycle wait period and follows with
another soft-start attempt, as shown in
Figure 11. This hiccup mode of operation repeats up to
seven times. On the eighth soft-start attempt, the part
latches off. Once latched off, the ISL6559 can only be reset
when the voltage on EN is brought below 1.23V or VCC is
brought below the POR falling threshold. Upon completion of
a successful soft-start attempt, operation will continue as
normal, PGOOD will return high, and the OC latch counter is
reset.
During VID-on-the-fly transitions, the OC comparator output
is blanked. The quality and mix of output capacitors used in
different applications leads to a wide output capacitance
range. Depending upon the magnitude and direction of the
VID change, the change in voltage across the output
capacitors could result in significant current flow. Summing
this instantaneous current with the load current already
present could drive the average current above the reference
current level and cause an OC trip during the transition. By
blanking the OC comparator during the VID-on-the-fly
transition, nuisance tripping is avoided.
General Design Guide
This design guide is intended to provide a high-level
explanation of the steps necessary to create a multi-phase
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced below. In
addition to this guide, Intersil provides complete reference
designs that include schematics, bills of materials, and
example board layouts for all common microprocessor
applications.
FN9084.8
December 29, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| X4043PIZ-4.5A | IC SUPERVISOR CPU 4K EE 8-DIP |
| ISL6558IR | IC REG CTRLR BUCK PWM 20-QFN |
| X4043PIZ-2.7A | IC SUPERVISOR CPU 4K EE 8-DIP |
| ISL6558IB-T | IC REG CTRLR BUCK PWM 16-SOIC |
| ISL6558IB | IC REG CTRLR BUCK PWM 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6559CB-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6559CBZ | 功能描述:电流型 PWM 控制器 2 TO 4 PHS BUCK CNTRLR 2 8LD RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6559CBZ-T | 功能描述:电流型 PWM 控制器 2 TO 4 PHS BUCK CNTRLR 2 8LD RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6559CR | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6559CR-T | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。