参数资料
| 型号： | ISL6569ACR-T |
| 厂商： | Intersil |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 32-QFN |
| 标准包装： | 6,000 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6569A
.
SAMPLED
channel current. Using Figures 4 and 6, the average current
CURRENT
V IN
is defined as:
DS ( ON )
I AVG = --------------- 2 -
I 1
I
r
R
SEN = I L 1 --------------------------
ISEN
CHANNEL 1
UPPER MOSFET
I 1 + I
2
(EQ. 4)
I AVG = ------------- ---------------------- )
R ISEN
SAMPLE
&
HOLD
-
R ISEN
I L1
I OUT r DS ( ON
2
where I OUT is the total load current.
-
+
ISL6569A INTERNAL CIRCUIT
ISEN1
I L 1 r DS ( ON )
+
CHANNEL 1
LOWER MOSFET
EXTERNAL CIRCUIT
The average current is then subtracted from the individual
channel sample currents. The resulting error current, I ER , is
then filtered before it adjusts V COMP . The modified V COMP
signal is compared to a sawtooth ramp signal and produces
a pulse width which corrects for any unbalance and drives
the error current toward zero. Figure 6 illustrates Intersil’s
FIGURE 4. CHANNEL 1 INTERNAL AND EXTERNAL
CURRENT-SENSING CIRCUITRY
Current Sensing
During the forced off time following a PWM transition low, the
controller senses channel load current by sampling the voltage
across the lower MOSFET r DS(ON) . A ground-referenced
amplifier, internal to the ISL6569A, connects to the PHASE
node through a resistor, R ISEN . The voltage across R ISEN is
equivalent to the voltage drop across the r DS(ON) of the lower
MOSFET while it is conducting. The resulting current into the
ISEN pin is proportional to the channel current, I L . The ISEN
current is then sampled and held after sufficient settling time
every switching cycle. The sampled current is used for channel-
current balance, load-line regulation, overcurrent protection,
and module current sharing.
The circuitry shown in Figure 4 represents channel-1 of a
two channel converter. This circuitry is repeated for
channel-2 of the converter. From Figure 4, the following
equation for channel-1 sampled current, I 1 , is derived
patented current balance method as implemented on one
channel of a multi-phase converter.
Two considerations designers face are MOSFET selection
and inductor design. Both are significantly improved when
channel currents track at any load level. The need for
complex drive schemes for multiple MOSFETs, exotic
magnetic materials, and expensive heat sinks is avoided.
Resulting in a cost-effective and easy to implement solution
relative to single-phase conversion. Channel current balance
insures the thermal advantage of multi-phase conversion is
realized. Heat dissipation is spread over multiple channels
and a greater area than single phase approaches.
In some circumstances, it may be necessary to deliberately
design some channel-current unbalance into the system. In
a highly compact design, one channel may be able to cool
more effectively than the other due to nearby air flow or heat
sinking components. The other channel may have more
difficulty cooling with comparatively less air flow and heat
sinking. The hotter channel may also be located close to
other heat-generating components tending to drive it’s
I 1 = I L1 ---------------------- )
r DS ( ON
R ISEN
(EQ. 3)
temperature even higher. In these cases, the proper
selection of the current sense resistors (R ISEN in Figure 4)
introduces channel current unbalance into the system.
Increasing the value of R ISEN in the cooler channel and
where I L1 is half of the total load current.
If r DS(ON) sensing is not desired, an independent current-
decreasing it in the hotter channel moves both channels into
thermal balance at the expense of current balance.
sense resistor in series with the lower MOSFET source can
serve as a sense element.
Channel-Current Balance
V COMP
+
-
+
-
PWM1
The sampled current from both channels, I 1 and I 2 , is used
to gauge both overall load current and the relative channel
f(j ω )
SAWTOOTH SIGNAL
current carried in each leg of the converter. The individual
sample currents are averaged. The resulting average
current, I AVG , provides a measure of the total load current
I ER
+
-
I AVG
÷ 2
Σ
I 2
demand on the converter and the appropriate level of
I 1
FIGURE 5. CHANNEL-1 PWM FUNCTION AND CURRENT-
BALANCE ADJUSTMENT
10
FN9092.2
December 29, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6569CR-T | IC REG CTRLR DIVIDER PWM 32-QFN |
| ISL6571CRZ | IC MOSF DRVR/SYNC SW COMPL 68QFN |
| ISL6611AIRZ | IC REG CTRLR DOUBLER PWM 16-QFN |
| ISL6617IRZ | IC PWM DOUBLER MONITOR 10DFN |
| ISL6627IRZ-T | IC CONTROLLER VR11.1 VR12 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6569ACRZ | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6569ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6569CB | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6569CB-T | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6569CBZ | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。