参数资料
| 型号： | ISL6569ACR-T |
| 厂商： | Intersil |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 32-QFN |
| 标准包装： | 6,000 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6569A
Following the delay, the soft start ramps linearly until V RAMP
reaches VID. For the system described above, this first linear
ramp will continue for approximately
PGOOD
t RAMP1 = ----------- – t DELAY
T SS
1.4
= 5.27ms
(EQ. 11)
UV
The final portion of the soft-start sequence is the time
remaining after V RAMP reaches VID and before I RAMP gets to
zero. This is also characterized by a slight change in the slope
of the output voltage ramp which, for the current example,
DAC
REFERENCE
+
350mV
-
POR
CIRCUIT
OC
-
+
90 μ A
I AVG
exists for a time of
t RAMP2 = T SS – t RAMP1 – t DELAY
= 2.34ms
(EQ. 12)
VDIFF
+
-
OV
OVP
t DELAY t RAMP1
t RAMP2
This behavior is seen in the example in Figure 10 of a converter
switching at 500kHz. For this converter, R FB is set to 2.67k ?
leading to T SS = 4.0ms, t DELAY = 700ns, t RAMP1 = 2.23ms,
and t RAMP2 = 1.17ms.
VOUT, 500mV/DIV
EN, 5V/DIV
1ms/div
FIGURE 10. SOFT-START WAVEFORMS FOR ISL6569A
BASED MULTI-PHASE BUCK CONVERTER
NOTE: Switching frequency 500kHz and R FB = 2.67k ?
Fault Monitoring and Protection
The ISL6569A actively monitors voltage and current
feedback to detect fault conditions. Fault monitors trigger
protective measures to prevent damage to a microprocessor
load. One common power good indication signal is provided
for linking to external system monitors. The schematic in
Figure 11 outlines the interaction between the fault monitors
and the power good signal.
Power Good Signal
The power good pin (PGOOD) is an open-drain logic output
which indicates that the converter is operating properly and
the output voltage is within a set window. The under-voltage
(UV) and over-voltage (OV) comparators create the output
voltage window. The controller also takes advantage of
current feedback to detect output over-current (OC)
14
2.2V
FIGURE 11. POWER GOOD AND PROTECTION CIRCUITRY
conditions. PGOOD pulls low during shutdown and releases
high during soft-start once the output voltage exceeds the
UV threshold. Once high, PGOOD will only transition low
when the controller is disabled or a fault condition is
detected. It will return high under certain circumstances
once a fault clears.
Under-Voltage Protection
The voltage on V DIFF is internally offset by 350mV before it
is compared with the DAC reference voltage. By positively
offsetting the output voltage, an UV threshold is created
which moves relative to the VID code. During soft-start, the
slow rising output voltage eventually exceeds the UV
threshold. Assuming the POR leg of the PGOOD NOR gate
has not detected an OC fault, the PGOOD signal will go
high.
If a fault condition arises during operation and the output
voltage drops below the UV threshold, PGOOD will
immediately pull low, but converter operation will continue.
PGOOD will return high once the output voltage surpasses
the UV threshold.
If the ISL6569A is disabled during operation, the PGOOD
signal will not pull low until the output voltage decays below
the UV threshold.
Over-Voltage Protection
When the output of the differential amplifier (VDIFF) reaches
2.2V, PGOOD immediately goes low indicating a fault. Two
protective actions are taken by the ISL6569A to protect the
microprocessor load.
First, all PWM outputs are commanded low. Directing the
Intersil drivers to turn on the lower MOSFETs; shunting the
output to ground preventing any further increase in output
voltage. The PWM outputs remain low until VDIFF falls to the
programmed DAC level at which time they go into a high-
FN9092.2
December 29, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6569CR-T | IC REG CTRLR DIVIDER PWM 32-QFN |
| ISL6571CRZ | IC MOSF DRVR/SYNC SW COMPL 68QFN |
| ISL6611AIRZ | IC REG CTRLR DOUBLER PWM 16-QFN |
| ISL6617IRZ | IC PWM DOUBLER MONITOR 10DFN |
| ISL6627IRZ-T | IC CONTROLLER VR11.1 VR12 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6569ACRZ | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6569ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6569CB | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6569CB-T | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6569CBZ | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。