- 您现在的位置：买卖IC网 > PDF目录15515 > ISL8103IRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL8103IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 1 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 66.6% |
| 电源电压： | 4.75 V ~ 12.6 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 剪切带 (CT) |
| 产品目录页面： | 1244 (CN2011-ZH PDF) |
| 其它名称： | ISL8103IRZ-TCT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ISL8103
1.6
ISL8103 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
1.4
VCC
1.2
1.0
0.8
POR
PVCC1
+ 12 V
0.6
0.4
Q GATE = 100nC
CIRCUIT
ENABLE
COMPARATOR
+
10.7k Ω
ENLL
0.2
20nC
50nC
-
1.40k Ω
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.66V
Δ V BOOT_CAP (V)
FIGURE 10. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
Gate Drive Voltage Versatility
The ISL8103 provides the user flexibility in choosing the
gate drive voltage for efficiency optimization. The controller
ties the upper and lower drive rails together. Simply applying
a voltage from 5V up to 12V on PVCC sets both gate drive
rail voltages simultaneously.
Initialization
Prior to initialization, proper conditions must exist on the
ENLL, VCC, PVCC and the REF0 and REF1 pins. When the
conditions are met, the controller begins soft-start. Once the
output voltage is within the proper window of operation, the
controller asserts PGOOD.
Enable and Disable
While in shutdown mode, the PWM outputs are held in a
high-impedance state to assure the drivers remain off. The
following input conditions must be met before the ISL8103 is
released from shutdown mode.
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL8103 is guaranteed. Hysteresis between the rising
and falling thresholds assure that once enabled, the
ISL8103 will not inadvertently turn off unless the bias
voltage drops substantially (see “Electrical
Specifications” on page 5).
15
SOFT-START
AND
FAULT LOGIC
FIGURE 11. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (ENLL) FUNCTION
2. The voltage on ENLL must be above 0.66V. The EN input
allows for power sequencing between the controller bias
voltage and another voltage rail. The enable comparator
holds the ISL8103 in shutdown until the voltage at ENLL
rises above 0.66V. The enable comparator has 100mV of
hysteresis to prevent bounce.
3. The driver bias voltage applied at the PVCC pins must
reach the internal power-on reset (POR) rising threshold.
In order for the ISL8103 to begin operation, PVCC1 is the
only pin that is required to have a voltage applied that
exceeds POR. However, for 2 or 3-phase operation
PVCC2 and PVCC3 must also exceed the POR
threshold. Hysteresis between the rising and falling
thresholds assure that once enabled, the ISL8103 will not
inadvertently turn off unless the PVCC bias voltage drops
substantially (see “Electrical Specifications” on page 5).
When each of these conditions is true, the controller
immediately begins the soft-start sequence.
Soft-Start
During soft-start, the DAC voltage ramps linearly from zero
to the programmed level. The PWM signals remain in the
high-impedance state until the controller detects that the
ramping DAC level has reached the output-voltage level.
This protects the system against the large, negative inductor
currents that would otherwise occur when starting with a
pre-existing charge on the output as the controller attempted
to regulate to zero volts at the beginning of the soft-start
cycle. The Output soft-start time, t SS , begins with a delay
period equal to 64 switching cycles after the ENLL has
exceeded its POR level, followed by a linear ramp with a rate
determined by the switching period, 1/F sw .
FN9246.1
July 21, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| IR3622AMTRPBF | IC REG CTRLR BUCK PWM VM 32MLPQ |
| 4590R-822K | INDUCTOR HIGH CURRENT 8.2UH |
| 4590-822K | INDUCTOR HIGH CURRENT 8.2UH |
| IR3621MTRPBF | IC REG CTRLR BUCK PWM VM 32MLPQ |
| MAX1771CPA+ | IC REG CTRLR BST PWM 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8104 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL8104CBZ | 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8104CBZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8104CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8104CRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。