- 您现在的位置：买卖IC网 > PDF目录15938 > ISL9217IRZ-T (Intersil)IC MULTI-CELL LI-ION PROT 24-QFN PDF资料下载
参数资料
| 型号： | ISL9217IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 22/33页 |
| 文件大小： | 0K |
| 描述： | IC MULTI-CELL LI-ION PROT 24-QFN |
| 标准包装： | 6,000 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 9.2 V ~ 31 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL9216, ISL9217
OVERCURRENT SAFETY FUNCTIONS
The ISL9216 continually monitors the discharge current by
monitoring the voltage at the CSENSE and DSENSE pins. If
that voltage exceeds a selected value for a time exceeding a
selected delay, then the device enters an overcurrent or short
circuit protection mode. In these modes, the ISL9216
automatically turns off both power FETs and hence prevents
current from flowing through the terminals P+ and P-.
The voltage thresholds and the response times of the
overcurrent protection circuits are selectable for discharge
overcurrent, charge overcurrent, and discharge short circuit
conditions. The specific settings are determined by bits in
the “DISCHARGE SET CONFIGURATION REGISTER
(ADDR: 05H)” on page 18, and “CHARGE/TIME SCALE
(See also “REGISTERS” on page 14).
In an overcurrent condition, the ISL9216 automatically turns off
the voltage on CFET and DFET pins. The DFET output drives
the discharge FET gate low, turning off the FET quickly. The
CFET output turns off and allows the gate of the charge FET to
be pulled low through a resistor.
By turning off the FETs the ISL9216 prevents damage to the
battery pack caused by excessive current into or out of the cells
(as in the case of a faulty charger or short circuit condition).
When the ISL9216 detects a discharge overcurrent condition,
the ISL9216 turns off both power FETs and sets the DOC bit.
(When the FETs are turned off, the DFET and CFET bits are
also reset). The automatic response to overcurrent during
discharge is prevented by setting the DENOCD bit to “1”. The
external microcontroller can turn on the FETs at any time to
recover from this condition, but it would usually turn on the load
monitor function (by setting the LDMONEN bit) and monitor the
LDFAIL bit to detect that the overcurrent condition has been
removed.
until the pack is removed from the charger and then re-
attached.
An alternative method of providing the protection function, if
desired by the designer, is to turn off the automatic safety
response. In this case, the ISL9216 device still monitors the
conditions and sets the status bits, but takes no action in
overcurrent or short circuit conditions. Safety of the pack
depends, instead, on the microcontroller to send commands to
the ISL9216 to turn off the FETs.
To facilitate a microcontroller response to an overcurrent
condition, especially if the microcontroller is in a low power
state, a charge overcurrent flag (COC), a discharge overcurrent
flag (DOC), or the short circuit flag (DSC) being set causes the
ISL9216 TEMP3V output to turn on and pull high. (See
Figure 5). This output can be used as an external interrupt by
the microcontroller to wake-up quickly to handle the overcurrent
condition.
LOAD MONITORING
The load monitor function in the ISL9216 (see Figure 4) is used
primarily to detect that the load has been removed following an
overcurrent or short circuit condition during discharge. This can
be used in a control algorithm to prevent the FETs from turning
on while the overload or short circuit condition remains.
The load monitor can also be used by the microcontroller
algorithms after an undervoltage condition on any cells
causes the FETs to turn off. Use of the load monitor prevents
the FETs from turning on while the load is still present. This
minimizes the possible “oscillations” that can occur when a
load is applied in a low capacity pack. It can also be part of a
system protection mechanism to prevent the load from
turning on automatically - i.e. some action must be taken
before the pack is again turned on.
P+
When the ISL9216 detects a discharge short circuit condition,
both power FETs are turned off and DSC bit is set. (When the
VSS
OPEN
R L
FETs are turned off, the DFET and CFET bits are also reset).
The automatic response to short circuit during discharge is
prevented by setting the DENSCD bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually turn on the load monitor
function (by setting the LDMONEN bit) and monitor the LDFAIL
ISL9216
DFET
VMON
R 1
P-
bit to detect that the overcurrent condition has been removed.
When the ISL9216 detects a charge overcurrent condition, both
power FETs are turned off and COC bit is set. (When the FETs
are turned off, the DFET and CFET bits are also reset). The
automatic response to overcurrent during discharge is
prevented by setting the DENOCC bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually wait to do this until the cell
LDFAIL
=1 if VMON > V VMONH
=0 if VMON ≤ V VMONL
LDMONEN
V REF
36V
voltages are not over charged and that the overcurrent
condition has been removed. Or, the microcontroller could wait
22
VSS
FIGURE 4. LOAD MONITOR CIRCUIT
FN6488.1
November 2, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HCC17DREF | CONN EDGECARD 34POS .100 EYELET |
| TWN2.00SV50 | THERMASHIELD WRAP 2" SLV 50' |
| HBC17DREF | CONN EDGECARD 34POS .100 EYELET |
| WWN1.00BK50 | WELD WRAP 1" BLACK 50' |
| VE-J64-EZ-F2 | CONVERTER MOD DC/DC 48V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219IRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| ISL9219IRZR5332 | 制造商:Intersil Corporation 功能描述:LI-ION BATTERY CHARGER, LOW VOLTAGE, 20LD QFN 3X4X0.9 - Rail/Tube 制造商:Intersil Corporation 功能描述:IC BATT CHRGR LI-ION/POL 20QFN 制造商:Intersil Corporation 功能描述:LI-ION BATRY CHRGR LW VAGE 20LD 3X4X0 9 |
发布紧急采购，3分钟左右您将得到回复。