- 您现在的位置：买卖IC网 > PDF目录15938 > ISL9217IRZ-T (Intersil)IC MULTI-CELL LI-ION PROT 24-QFN PDF资料下载
参数资料
| 型号： | ISL9217IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 28/33页 |
| 文件大小： | 0K |
| 描述： | IC MULTI-CELL LI-ION PROT 24-QFN |
| 标准包装： | 6,000 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 9.2 V ~ 31 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页
ISL9216, ISL9217
When data is clocked into the ISL9216 through the I 2 C port, it
is immediately transferred to the serial cascade port, so both
the ISL9216 and ISL9217 see the slave byte at the same
time. After the 8th slave bit, the device that receives the
correct slave byte sends an acknowledge, while the other
device ignores all subsequent data on the serial port until it
receives a stop bit. However, even though the ISL9216
ignores the data, it still passes it through to the ISL9217.
The SDAI and SDAO pins of the ISL9217 need to have pull-
up resistors of approximately 4.7k Ω , since the output drivers
are open-drain devices.
Register Protection
The Discharge Set, Charge Set, and Feature Set
Write the FSETEN bit (Addr 8:bit 7) to “1” to change the data
in the Feature Set register (Address 7).
Write the CHSETEN bit (Addr 8:bit 6) to “1” to change the
data in the Feature Set register (Address 6).
Write the DISSETEN bit (Addr 8:bit 5) to “1” to change the
data in the Feature Set register (Address 5).
The microcontroller can reset these bits back to zero to
prevent inadvertent writes that change the operation of the
pack.
Operation State Machine
Figure 16 shows a device state machine which defines how
the ISL9216 and ISL9217 respond to various conditions.
configuration registers are write protected on initial power-
up. In order to write to these registers it is necessary to set a
bit to enable each one. These write enable bits are in the
Write Enable register (Address 08H).
Power Fails and one of the supplies, V CC , V CELL1 , V CELL2 ,
and V CELL3 do not meet minimum voltage requirements
POWER-DOWN STATE
I 2 C interface is disabled. Biasing is disabled.
All registers set to default values (All “0”)
Power is applied and all of the supplies, V CC , V CELL1 ,
V CELL2 , and V CELL3 meet minimum voltage requirements
POWER-UP STATE
I 2 C interface is enabled. Biasing is enabled.
Voltage Regulator is enabled.
MAIN OPERATING STATE
Voltage Regulator is ON
Logic and registers are powered by RGO
SLEEP STATE
Voltage Regulator is OFF
Biasing is OFF
CFET, DFET, Cell balancing outputs are all off.
(Require external command to turn on)
Charge and discharge current protection
circuits and temperature protection circuits are
active (Default). Overcurrent conditions force
power FETs to turn off. Over-temperature
conditions force power FETs and cell balance
outputs to turn off.
Voltage and temperature monitoring circuits
are awaiting external control.
SLEEP bit is set to ‘1’
WKUP goes above or below
threshold (edge triggered).
[ISL9217 wake-up requires μC
command to ISL9216].
Or, SLEEP bit is set to ‘0’
Logic and registers are powered by V CELL1
CFET, DFET, Cell balancing outputs are all off.
Charge and discharge current protection
circuits all off.
Voltage and temperature monitoring circuits
are off.
I 2 C communication is active (if V CELL1 voltage
is high enough to operate with external
device.)
FIGURE 16. DEVICE OPERATION STATE MACHINE
28
FN6488.1
November 2, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HCC17DREF | CONN EDGECARD 34POS .100 EYELET |
| TWN2.00SV50 | THERMASHIELD WRAP 2" SLV 50' |
| HBC17DREF | CONN EDGECARD 34POS .100 EYELET |
| WWN1.00BK50 | WELD WRAP 1" BLACK 50' |
| VE-J64-EZ-F2 | CONVERTER MOD DC/DC 48V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219IRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| ISL9219IRZR5332 | 制造商:Intersil Corporation 功能描述:LI-ION BATTERY CHARGER, LOW VOLTAGE, 20LD QFN 3X4X0.9 - Rail/Tube 制造商:Intersil Corporation 功能描述:IC BATT CHRGR LI-ION/POL 20QFN 制造商:Intersil Corporation 功能描述:LI-ION BATRY CHRGR LW VAGE 20LD 3X4X0 9 |
发布紧急采购，3分钟左右您将得到回复。