- 您现在的位置：买卖IC网 > PDF目录15938 > ISL9217IRZ-T (Intersil)IC MULTI-CELL LI-ION PROT 24-QFN PDF资料下载
参数资料
| 型号： | ISL9217IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 23/33页 |
| 文件大小： | 0K |
| 描述： | IC MULTI-CELL LI-ION PROT 24-QFN |
| 标准包装： | 6,000 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 9.2 V ~ 31 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL9216, ISL9217
The load monitor circuit can be turned on or off by the
microcontroller. It is normally turned off to minimize current
consumption. It must be activated by the external
microcontroller for it to operate. The circuit works by
internally connecting the VMON pin to VSS through a
resistor. The circuit operates as shown in Figure 4.
In a typical pack operation, when an overcurrent or short
circuit event happens, the DFET turns off, opening the
battery circuit to the load. At this time, the R L is small and
the load monitor is initially off. In this condition, the voltage at
VMON could rise to nearly the pack voltage. However, since
in most configurations, this voltage would exceed the
maximum limits on the VMON pin, a series zener diode is
required.
Once the power FETs turn off, the microcontroller activates
the load monitor by setting the LDMONEN bit. This turns on
an internal FET that adds a pull-down resistor to the load
monitor circuit. While still in the overload condition the
combination of the load resistor, an external adjustment
resistor (R 1 ), the zener diode, and the internal load monitor
resistor form a voltage divider. R 1 is chosen so that when the
load is released to a sufficient level, the LDFAIL condition is
reset.
Because of the manual scan of the temperature, it may be
desired to turn off the automatic scan, although they can be
used at the same time without interference. To turn off the
automatic scan, set the ATMPOFF bit.
The microcontroller can over-ride both the automatic
temperature scan and the microcontroller controlled
temperature scan by setting the TEMP3ON configuration bit.
This turns on the TEMP3V output to keep the temperature
control voltage on all the time, for a continuous monitoring of
an over-temperature condition. This likely will consume a
significant amount of current, so this feature is usually used
for special or test purposes.
Protection
As a default, when the ISL9216 detects an internal or
external over-temperature condition, the FETs are turned off,
the cell balancing function is disabled, and the IOT bit or
XOT bit (respectively) is set.
Turning off the FETs in the event of an over-temperature
condition prevents continued discharge or charge of the cells
when they are over heated. Turning off the cell balancing in
the event of an over-temperature condition prevents damage
to the IC in the event too many cells are being balanced,
causing too much power dissipation in the ISL9216.
OVER-TEMPERATURE SAFETY FUNCTIONS
External Temperature Control
The external temperature is monitored by using a voltage
divider consisting of a fixed resistor and a thermistor. This
ISL9216
5ms
635ms
divider is powered by the ISL9216 TEMP3V output. This
output is normally controlled so it is on for only short periods
I 2 C
I 2 C
OSC
to minimize current consumption.
Without microcontroller intervention, the ISL9216
continuously turns on TEMP3V output (and the external
temperature monitor) for 5ms every 640ms. In this way, the
external temperature is monitored even if the microcontroller
is asleep. If the ATMPOFF bit is set, this automatic
ATMPOFF
TMP3ON
temperature scan is turned off.
When the TEMP3V output turns on, the ISL9216 waits 1ms
AO3:AO0
DECODE
RGO
TO
μC
for the temperature reading to stabilize, then compares the
external temperature voltage with an internal voltage divider
that is set to TEMP3V/13. When the thermistor voltage is
EXT TEMP
TEMP3V
R X
below the reference threshold after the delay, an external
temperature fail condition exists. To set the external over-
AO
MUX
VSS (ON)
TEMPI
temperature limit, set the value of R X resistor to the 12 times
the resistance of the thermistor at the over-temperature
threshold.
1ms
DELAY
EXTERNAL
TEMP
The TEMP3V output pin also turns on when the
microcontroller sets the AO3:AO0 bits to select that the
external temperature voltage. This causes the TEMPI voltage
XOT
TEMP FAIL
INDICATOR
MONITOR
VSS
to be placed on AO and activates (after 1ms) the over-
temperature detection. As long as the AO3:AO0 bits point to
the external temperature, the TEMP3V output remains on.
23
FIGURE 5. EXTERNAL TEMPERATURE MONITORING AND
CONTROL (ISL9216 ONLY)
FN6488.1
November 2, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HCC17DREF | CONN EDGECARD 34POS .100 EYELET |
| TWN2.00SV50 | THERMASHIELD WRAP 2" SLV 50' |
| HBC17DREF | CONN EDGECARD 34POS .100 EYELET |
| WWN1.00BK50 | WELD WRAP 1" BLACK 50' |
| VE-J64-EZ-F2 | CONVERTER MOD DC/DC 48V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL9219IRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| ISL9219IRZR5332 | 制造商:Intersil Corporation 功能描述:LI-ION BATTERY CHARGER, LOW VOLTAGE, 20LD QFN 3X4X0.9 - Rail/Tube 制造商:Intersil Corporation 功能描述:IC BATT CHRGR LI-ION/POL 20QFN 制造商:Intersil Corporation 功能描述:LI-ION BATRY CHRGR LW VAGE 20LD 3X4X0 9 |
发布紧急采购，3分钟左右您将得到回复。