参数资料
| 型号： | ISL97522IRZ-TK |
| 厂商： | Intersil |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | IC SUPPLY CTRL 4CH TFT-LCD 38QFN |
| 标准包装： | 1,000 |
| 应用： | LCD 电视机/监控器 |
| 电流 - 电源： | 3mA |
| 电源电压： | 4.5 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-VFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
ISL97522
0.1μF
ISINB
Set-Up LDOs Output Voltage
Refer to Typical Application Diagram, the output voltages of
V ON , V OFF , and V LOGIC are determined by Equations 11
and 12:
V ON = V FBP × ? 1 + ---------- ?
V OFF = V FBN + ---------- × ( V FBN – V REF )
R
PG_LDON
0.4V
-
+
LDO_OFF
FBN
V REF
R N2
CP (TO -26V)
0.1μF
? R 12 ?
? R 11 ?
R 22
21
(EQ. 11)
(EQ. 12)
-
+
GMN
1 : Nn
36V
DRVN
R BN
3k Ω
R N1
V OFF (TO -20V)
C OFF
Charge Pump
To generate an output voltage higher than A VDD , single or
multi stages of charge pumps are needed. The number of
stage is determined by the input and output voltage. For
positive charge pump stages:
N POSITIVE ≥ --------------------------------------------------------------
ESD
CLAMP
V OUT + V CE – V INPUT
V INPUT – 2 × V F
(EQ. 13)
FIGURE 18. V OFF FUNCTION BLOCK DIAGRAM
The V ON power supply is used to power the positive supply
of the row driver in the LCD panel. The DC/DC consists of an
external diode-capacitor charge pump powered from the
switch node (LXB) of the A VDD converter, followed by a low
where V CE is the dropout voltage of the pass component of
the linear regulator. It ranges from 0.3V to 1V depending on
the transistor. V F is the forward-voltage of the charge pump
rectifier diode.
The number of negative charge pump stages is given by:
N NEGATIVE ≥ -------------------------------------------------
dropout linear regulator (LDO_ON). The LDO_ON regulator
uses an external PNP transistor as the pass element. The
onboard LDO controller is a wide band (>10MHz)
V OUTPUT + V CE
V INPUT – 2 × V F
(EQ. 14)
transconductance amplifier capable of 5mA output current,
which is sufficient for up to 50mA or more output current
under the low dropout condition (forced beta of 10). Typical
V ON voltage supported by the ISL97522 ranges from +15V
to +36V. A fault comparator is also included for monitoring
the output voltage. The undervoltage threshold is set at
16.7% below the 1.2V reference.
The V OFF power supply is used to power the negative
To achieve high efficiency and low material cost, the lowest
number of charge pump stages, which can meet the above
requirements, is always preferred.
Charge Pump Output Capacitors
A ceramic capacitor with low ESR is recommended. With
ceramic capacitors, the output ripple voltage is dominated by
the capacitance value. The capacitance value can be
chosen by Equation 15.
C OUT ≥ ------------------------------------------------------
supply of the row driver in the LCD panel. The DC/DC
consists of an external diode-capacitor charge pump
powered from the switch node (LXB) of the A VDD converter,
I OUT
2 × V RIPPLE × f OSC
(EQ. 15)
followed by a low dropout linear regulator (LDO_OFF). The
LDO_OFF regulator uses an external NPN transistor as the
pass element. The onboard LDO controller is a wide band
(>10MHz) transconductance amplifier capable of 5mA
output current, which is sufficient for up to 50mA or more
output current under the low dropout condition (forced beta
of 10). Typical V OFF voltage supported by the ISL97522
ranges from -5V to -25V. A fault comparator is also included
for monitoring the output voltage. The undervoltage
threshold is set at 20% above the 1.0V reference level.Set-
Up LDOs Output Voltage.
14
Where f SOC is the switching frequency.
High Charge Pump Output Voltage (>36V)
Applications
In the applications where the charge pump output voltage is
over 36V, an external npn transistor need to be inserted into
between DRVP pin and base of pass transistor Q3 as shown
in Figure 19; or the linear regulator can control only one
stage charge pump and regulate the final charge pump
output as shown in Figure 20.
FN7445.0
December 13, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97536IUZ | IC REG BUCK SYNC ADJ 1A 10MSOP |
| ISL97642IRTZ | IC REG TFT-LCD DC/DC 32-TQFN |
| ISL97644IRZ-T | IC REG BOOST LDO VON VCOM 24-QFN |
| ISL97645AIRZ | IC REG BOOST VON VCOM 24-QFN |
| ISL97646IRZ-TK | IC REG BOOST LDO VON VCOM 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97536IUZ | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL97536IUZ-T | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| ISL97536IUZ-TK | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| ISL97631HTZ-T7A | 制造商:Intersil Corporation 功能描述: |
| ISL97631IHTZ | 制造商:Intersil 功能描述:6 LEDs Driver with Integrated Schottky Diode with OVP |
发布紧急采购，3分钟左右您将得到回复。