参数资料
| 型号： | ISL97522IRZ-TK |
| 厂商： | Intersil |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC SUPPLY CTRL 4CH TFT-LCD 38QFN |
| 标准包装： | 1,000 |
| 应用： | LCD 电视机/监控器 |
| 电流 - 电源： | 3mA |
| 电源电压： | 4.5 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-VFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
ISL97522
Buck Inductor
An inductor value in the range 3.3-10μH is recommended for
the buck converter. Besides the inductance, the DC
resistance and the saturation current should also be
considered when choosing buck inductor. Low DC
resistance can help maintain high efficiency, and the
saturation current rating should be at least maximum output
current plus half of ripple current.
Buck MOSFET
The principle to select Buck MOSFET is similar to that of
Boost. The voltage of stress of buck converter should be
maximum input voltage plus reasonable margin, and the
current rating should be over the maximum output current.
The r DS(ON) of this MOSFET should be in the range from
20m Ω to 50m Ω .
Rectifier Diode (Buck Converter)
A Schottky diode is recommended due to fast recovery and
low forward voltage. The reverse voltage rating should be
higher than the maximum input voltage. The average current
should be as the following equation,
minimum load can be adjusted by the feedback resistors
to FBL.
The bootstrap capacitor can only be charged when the
higher side MOSFET is off. If the load is too light which can
not make the on time of the low side diode be sufficient to
replenish the boot strap capacitor, the MOSFET can’t turn
on. Hence there is minimum load requirement to charge the
bootstrap capacitor properly.
Start-Up Sequence
Figure 21 shows a detailed start-up sequence waveform. For
a successful power-up, there should be six peaks at V CDLY .
When a fault is detected, the device will latch off until either
EN is toggled or the input supply is recycled.
If EN is L, the device is powered down. If EN is H, and the
input voltage (V IN ) exceeds 2.5V, an internal current source
starts to charge C DLY to an upper threshold using a fast
ramp followed by a slow ramp. If EN is low at this point, the
C DLY ramp will be delayed until EN goes high.
The first four ramps on C DLY (two up, two down) are used to
initialize the fault protection switch and to check whether
I AVG = ( 1 – D ) *I O
(EQ. 19)
there is a fault condition on C DLY or V REF . If a fault is
detected, the outputs and the input protection will turn off
and the chip will power down.
Where I O is the output current of buck converter.
Output Capacitor (Buck Converter)
Four 10μF or two 22μF ceramic capacitors are
recommended for this part. The overshoot and undershoot
will be reduced with more capacitance, but the recovery time
will be longer.
PI Loop Compensation (Buck Converter)
The buck converter of ISL97522 can be compensated by a
RC network connected from CINTL pin to ground. C27 =
4.7nF and R17= 2k RC network is used in the demo board.
The larger value resistor can lower the transient overshoot,
however, at the expense of stability of the loop.
The stability can be optimized in a similar manner to that
described in the section on "PI Loop Compensation (Boost
Converter)”.
Bootstrap Capacitor (C28)
This capacitor is used to provide the supply to the high driver
circuitry for the buck MOSFET. The bootstrap supply is
formed by an internal diode and capacitor combination. A
1μF is recommended for ISL97522. A low value capacitor
can lead to overcharging and in turn damage the part.
If the load is too light, the on-time of the low side diode may
be insufficient to replenish the bootstrap capacitor voltage. In
this case, if V IN -V BUCK < 1.5V, the internal MOSFET pull-up
device may be unable to turn-on until V LOGIC falls. Hence,
there is a minimum load requirement in this case. The
16
If no fault is found, C CDLY continues ramping up and down
until the sequence is completed.
During the second ramp, the device checks the status of
V REF and over temperature.
Initially the boost is not enabled so V BOOST rises to V IN -
V DIODE through the output diode. Hence, there is a step at
V BOOST during this part of the start-up sequence. If this step
is not desirable, an external PMOS FET can be used to delay
the output until the boost is enabled internally. The delayed
output appears at A VDD .
V BOOST soft-starts at the beginning of the third ramp. The
soft-start ramp depends on the value of the C DLY capacitor.
For C DLY of 220nF, the soft-start time is ~2ms.
V OFF turns on at the start of the fourth peak. At the fifth
peak, the open drain o/p DELB goes low to turn on the
external PMOS Q3 to generate a delayed V BOOST output.
V ON is enabled at the beginning of the sixth ramp. A VDD ,
V OFF , DELB and V ON are checked at end of this ramp.
Vlogic’s start-up is controlled by ENL. When ENL is L, Vlogic
is off, and when ENL is H, V LOGIC is on.
FN7445.0
December 13, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97536IUZ | IC REG BUCK SYNC ADJ 1A 10MSOP |
| ISL97642IRTZ | IC REG TFT-LCD DC/DC 32-TQFN |
| ISL97644IRZ-T | IC REG BOOST LDO VON VCOM 24-QFN |
| ISL97645AIRZ | IC REG BOOST VON VCOM 24-QFN |
| ISL97646IRZ-TK | IC REG BOOST LDO VON VCOM 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97536IUZ | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL97536IUZ-T | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| ISL97536IUZ-TK | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| ISL97631HTZ-T7A | 制造商:Intersil Corporation 功能描述: |
| ISL97631IHTZ | 制造商:Intersil 功能描述:6 LEDs Driver with Integrated Schottky Diode with OVP |
发布紧急采购，3分钟左右您将得到回复。