参数资料
| 型号： | ISLA222P13IRZ |
| 厂商： | Intersil |
| 文件页数： | 17/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SRL/SPI 72QFN |
| 标准包装： | 1 |
| 系列： | FemtoCharge™ |
| 位数： | 12 |
| 采样率（每秒）： | 130M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 697mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 72-VFQFN 裸露焊盘 |
| 供应商设备封装： | 72-QFN（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISLA222P
24
FN7853.1
June 17, 2011
and N-byte transfers, respectively. The operation for a 3-byte
transfer can be inferred from these diagrams.
SPI Configuration
ADDRESS 0X00: CHIP_PORT_CONFIG
Bit ordering and SPI reset are controlled by this register. Bit order
can be selected as MSB to LSB (MSB first) or LSB to MSB (LSB
first) to accommodate various micro controllers.
Bit 7 SDO Active
Bit 6 LSB First
Setting this bit high configures the SPI to interpret serial data
as arriving in LSB to MSB order.
Bit 5 Soft Reset
Setting this bit high resets all SPI registers to default values.
Bit 4 Reserved
This bit should always be set high.
Bits 3:0 These bits should always mirror bits 4:7 to avoid
ambiguity in bit ordering.
ADDRESS 0X02: BURST_END
If a series of sequential registers are to be set, burst mode can
improve throughput by eliminating redundant addressing. In
3-wire SPI mode, the burst is ended by pulling the CSB pin high. If
the device is operated in 2-wire mode the CSB pin is not
available. In that case, setting the burst_end address determines
the end of the transfer. During a write operation, the user must
be cautious to transmit the correct number of bytes based on the
starting and ending addresses.
Bits 7:0 Burst End Address
This register value determines the ending address of the burst
data.
Device Information
ADDRESS 0X08: CHIP_ID
ADDRESS 0X09: CHIP_VERSION
The generic die identifier and a revision number, respectively, can
be read from these two registers.
Device Configuration/Control
A common SPI map, which can accommodate single-channel or
multi-channel devices, is used for all Intersil A/D products.
ADDRESS 0X20: OFFSET_COARSE_ADC0
ADDRESS 0X21: OFFSET_FINE_ADC0
The input offset of the A/D core can be adjusted in fine and
coarse steps. Both adjustments are made via an 8-bit word as
detailed in Table 5. The data format is twos complement.
The default value of each register will be the result of the
self-calibration after initial power-up. If a register is to be
incremented or decremented, the user should first read the
register value then write the incremented or decremented value
back to the same register.
ADDRESS 0X22: GAIN_COARSE_ADC0
ADDRESS 0X23: GAIN_MEDIUM_ADC0
ADDRESS 0X24: GAIN_FINE_ADC0
Gain of the A/D core can be adjusted in coarse, medium and fine
steps. Coarse gain is a 4-bit adjustment while medium and fine
are 8-bit. Multiple Coarse Gain Bits can be set for a total
adjustment range of ±4.2%. (‘0011’
-4.2% and ‘1100’ +4.2%)
It is recommended to use one of the coarse gain settings (-4.2%,
-2.8%, -1.4%, 0, 1.4%, 2.8%, 4.2%) and fine-tune the gain using the
registers at 0x0023 and 0x24.
The default value of each register will be the result of the
self-calibration after initial power-up. If a register is to be
incremented or decremented, the user should first read the
register value then write the incremented or decremented value
back to the same register.
TABLE 4. BYTE TRANSFER SELECTION
[W1:W0]
BYTES TRANSFERRED
00
1
01
2
10
3
11
4 or more
TABLE 5. OFFSET ADJUSTMENTS
PARAMETER
0x20[7:0]
COARSE OFFSET
0x21[7:0]
FINE OFFSET
Steps
255
–Full-Scale (0x00)
-133LSB (-47mV)
-5LSB (-1.75mV)
Mid–Scale (0x80)
0.0LSB (0.0mV)
0.0LSB
+Full-Scale (0xFF)
+133LSB (+47mV)
+5LSB (+1.75mV)
Nominal Step Size
1.04LSB (0.37mV)
0.04LSB (0.014mV)
TABLE 6. COARSE GAIN ADJUSTMENT
0x22[3:0] CORE 0
0x26[3:0] CORE 1
NOMINAL COARSE GAIN ADJUST
(%)
Bit3
+2.8
Bit2
+1.4
Bit1
-2.8
Bit0
-1.4
相关PDF资料 |
PDF描述 |
|---|---|
| ISLA224S25IR1Z | IC ADC |
| KAD2708C-27Q68 | IC ADC 8BIT 275MSPS PAR 68-QFN |
| KAD2708L-27Q68 | IC ADC 8BIT 275MSPS PAR 68-QFN |
| KAD2710C-27Q68 | IC ADC 10BIT 275MSPS PAR 68-QFN |
| KAD2710L-21Q68 | IC ADC 10BIT 210MSPS SGL 68-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISLA222P20 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC |
| ISLA222P20IRZ | 功能描述:IC ADC 12BIT SRL/SPI 72QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:FemtoCharge™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 位数:10 采样率（每秒）:357k 数据接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 转换器数目:1 功率耗散（最大）:830µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:剪切带 (CT) 输入数目和类型:2 个单端，单极；2 个单端，双极；1 个差分，单极；1 个差分，双极 产品目录页面:1396 (CN2011-ZH PDF) 其它名称:MAX1395ETB+TCT |
| ISLA222P25 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC |
| ISLA222P25IRZ | 制造商:Intersil Corporation 功能描述:12-BIT 250MSPS DUAL ADC, 72-PIN QFN - Trays 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SRL/SPI 72QFN 制造商:Intersil 功能描述:12-BIT 250MSPS DL AD C 72-PIN |
| ISLA222S | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 12-Bit, 250/200/125 MSPS JESD204B High Speed Serial Output ADC |
发布紧急采购，3分钟左右您将得到回复。