参数资料
| 型号： | ISLA222P13IRZ |
| 厂商： | Intersil |
| 文件页数： | 8/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SRL/SPI 72QFN |
| 标准包装： | 1 |
| 系列： | FemtoCharge™ |
| 位数： | 12 |
| 采样率（每秒）： | 130M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 697mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 72-VFQFN 裸露焊盘 |
| 供应商设备封装： | 72-QFN（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | * |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISLA222P
16
FN7853.1
June 17, 2011
Theory of Operation
Functional Description
The ISLA222P is based on a 12-bit, 250MSPS A/D converter core
that utilizes a pipelined successive approximation architecture
(see Figure 20). The input voltage is captured by a Sample-Hold
Amplifier (SHA) and converted to a unit of charge. Proprietary
charge-domain techniques are used to successively compare the
input to a series of reference charges. Decisions made during the
successive approximation operations determine the digital code
for each input value. Digital error correction is also applied,
resulting in a total latency of 10 clock cycles. This is evident to the
user as a latency between the start of a conversion and the data
being available on the digital outputs.
Power-On Calibration
As mentioned previously, the cores perform a self-calibration at
start-up. An internal power-on-reset (POR) circuit detects the
supply voltage ramps and initiates the calibration when the
analog and digital supply voltages are above a threshold. The
following conditions must be adhered to for the power-on
calibration to execute successfully:
A frequency-stable conversion clock must be applied to the
CLKP/CLKN pins
DNC pins must not be connected
SDO has an internal pull-up and should not be driven externally
RESETN is pulled low by the ADC internally during POR.
External driving of RESETN is optional.
SPI communications must not be attempted
A user-initiated reset can subsequently be invoked in the event
that the above conditions cannot be met at power-up.
After the power supply has stabilized, the internal POR releases
RESETN and an internal pull-up pulls it high, which starts the
calibration sequence. If a subsequent user-initiated reset is
desired, the RESETN pin should be connected to an open-drain
driver with an off-state/high impedance state leakage of less
than 0.5mA to assure exit from the reset state so calibration can
start.
The calibration sequence is initiated on the rising edge of
RESETN, as shown in Figure 19. Calibration status can be
determined by reading the cal_status bit (LSB) at 0xB6. This bit is
‘0’ during calibration and goes to a logic ‘1’ when calibration is
complete. The data outputs produce 0xCCCC during calibration;
this can also be used to determine calibration status.
While RESETN is low, the output clock (CLKOUTP/CLKOUTN) is
set low. Normal operation of the output clock resumes at the
next input clock edge (CLKP/CLKN) after RESETN is de-asserted.
At 250MSPS the nominal calibration time is 200ms, while the
maximum calibration time is 550ms.
FIGURE 19. CALIBRATION TIMING
CLKP
CLKN
CLKOUTP
CALIBRATION
BEGINS
CALIBRATION
COMPLETE
CALIBRATION
TIME
RESETN
CAL_STATUS
BIT
FIGURE 20. A/D CORE BLOCK DIAGRAM
DIGITAL
ERROR
CORRECTION
SHA
1.25V
INP
INN
CLOCK
GENERATION
2.5- BIT
FLASH
6- STAGE
1.5- BIT/ STAGE
3- STAGE
1-BIT/ STAGE
3- BIT
FLASH
LVDS/LVCMOS
OUTPUTS
+
–
FLASH
2.5-BIT
相关PDF资料 |
PDF描述 |
|---|---|
| ISLA224S25IR1Z | IC ADC |
| KAD2708C-27Q68 | IC ADC 8BIT 275MSPS PAR 68-QFN |
| KAD2708L-27Q68 | IC ADC 8BIT 275MSPS PAR 68-QFN |
| KAD2710C-27Q68 | IC ADC 10BIT 275MSPS PAR 68-QFN |
| KAD2710L-21Q68 | IC ADC 10BIT 210MSPS SGL 68-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISLA222P20 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC |
| ISLA222P20IRZ | 功能描述:IC ADC 12BIT SRL/SPI 72QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:FemtoCharge™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 位数:10 采样率（每秒）:357k 数据接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 转换器数目:1 功率耗散（最大）:830µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:剪切带 (CT) 输入数目和类型:2 个单端，单极；2 个单端，双极；1 个差分，单极；1 个差分，双极 产品目录页面:1396 (CN2011-ZH PDF) 其它名称:MAX1395ETB+TCT |
| ISLA222P25 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC |
| ISLA222P25IRZ | 制造商:Intersil Corporation 功能描述:12-BIT 250MSPS DUAL ADC, 72-PIN QFN - Trays 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SRL/SPI 72QFN 制造商:Intersil 功能描述:12-BIT 250MSPS DL AD C 72-PIN |
| ISLA222S | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 12-Bit, 250/200/125 MSPS JESD204B High Speed Serial Output ADC |
发布紧急采购，3分钟左右您将得到回复。