参数资料
| 型号： | ISLA222P13IRZ |
| 厂商： | Intersil |
| 文件页数： | 25/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SRL/SPI 72QFN |
| 标准包装： | 1 |
| 系列： | FemtoCharge™ |
| 位数： | 12 |
| 采样率（每秒）： | 130M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 697mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 72-VFQFN 裸露焊盘 |
| 供应商设备封装： | 72-QFN（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISLA222P
31
FN7853.1
June 17, 2011
A/D Evaluation Platform
Intersil offers an A/D Evaluation platform which can be used to
evaluate any of Intersil’s high speed A/D products. The platform
consists of a FPGA based data capture motherboard and a family
of A/D daughtercards. This USB based platform allows a user to
quickly evaluate the A/D’s performance at a user’s specific
application frequency requirements. More information is
available at
Layout Considerations
Split Ground and Power Planes
Data converters operating at high sampling frequencies require
extra care in PC board layout. Many complex board designs
benefit from isolating the analog and digital sections. Analog
supply and ground planes should be laid out under signal and
clock inputs. Locate the digital planes under outputs and logic
pins. Grounds should be joined under the chip.
Clock Input Considerations
Use matched transmission lines to the transformer inputs for the
analog input and clock signals. Locate transformers and
terminations as close to the chip as possible.
Exposed Paddle
The exposed paddle must be electrically connected to analog
ground (AVSS) and should be connected to a large copper plane
using numerous vias for optimal thermal performance.
Bypass and Filtering
Bulk capacitors should have low equivalent series resistance.
Tantalum is a good choice. For best performance, keep ceramic
bypass capacitors very close to device pins. Longer traces will
increase inductance, resulting in diminished dynamic
performance and accuracy. Make sure that connections to
ground are direct and low impedance. Avoid forming ground
loops.
LVDS Outputs
Output traces and connections must be designed for 50
Ω (100Ω
differential) characteristic impedance. Keep traces direct and
minimize bends where possible. Avoid crossing ground and
power-plane breaks with signal traces.
LVCMOS Outputs
Output traces and connections must be designed for 50
Ω
characteristic impedance.
Unused Inputs
Standard logic inputs (RESETN, CSB, SCLK, SDIO and SDO) which
will not be operated do not require connection to ensure optimal
A/D performance. These inputs can be left floating if they are not
used. Tri-level inputs (NAPSLP) accept a floating input as a valid
state, and therefore should be biased according to the desired
functionality.
Definitions
Analog Input Bandwidth is the analog input frequency at which
the spectral output power at the fundamental frequency (as
determined by FFT analysis) is reduced by 3dB from its full-scale
low-frequency value. This is also referred to as Full Power
Bandwidth.
Aperture Delay or Sampling Delay is the time required after the
rise of the clock input for the sampling switch to open, at which
time the signal is held for conversion.
Aperture Jitter is the RMS variation in aperture delay for a set of
samples.
Clock Duty Cycle is the ratio of the time the clock wave is at logic
high to the total time of one clock period.
Differential Non-Linearity (DNL) is the deviation of any code width
from an ideal 1 LSB step.
FIGURE 49. VCM_OUT OUTPUT
Equivalent Circuits (Continued)
VCM
AVDD
0.94V
+
–
相关PDF资料 |
PDF描述 |
|---|---|
| ISLA224S25IR1Z | IC ADC |
| KAD2708C-27Q68 | IC ADC 8BIT 275MSPS PAR 68-QFN |
| KAD2708L-27Q68 | IC ADC 8BIT 275MSPS PAR 68-QFN |
| KAD2710C-27Q68 | IC ADC 10BIT 275MSPS PAR 68-QFN |
| KAD2710L-21Q68 | IC ADC 10BIT 210MSPS SGL 68-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISLA222P20 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC |
| ISLA222P20IRZ | 功能描述:IC ADC 12BIT SRL/SPI 72QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:FemtoCharge™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 位数:10 采样率（每秒）:357k 数据接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 转换器数目:1 功率耗散（最大）:830µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:剪切带 (CT) 输入数目和类型:2 个单端，单极；2 个单端，双极；1 个差分，单极；1 个差分，双极 产品目录页面:1396 (CN2011-ZH PDF) 其它名称:MAX1395ETB+TCT |
| ISLA222P25 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC |
| ISLA222P25IRZ | 制造商:Intersil Corporation 功能描述:12-BIT 250MSPS DUAL ADC, 72-PIN QFN - Trays 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SRL/SPI 72QFN 制造商:Intersil 功能描述:12-BIT 250MSPS DL AD C 72-PIN |
| ISLA222S | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 12-Bit, 250/200/125 MSPS JESD204B High Speed Serial Output ADC |
发布紧急采购，3分钟左右您将得到回复。