参数资料
| 型号： | IXDS502D1B |
| 厂商： | IXYS |
| 文件页数： | 10/11页 |
| 文件大小： | 0K |
| 描述： | IC GATE LS DRVR SGL 2A 6-DFN |
| 标准包装： | 121 |
| 类型： | 低端 |
| 输入类型： | 非反相 |
| 输出数： | 1 |
| 导通状态电阻： | 4 欧姆 |
| 电流 - 输出 / 通道： | 500mA |
| 电流 - 峰值输出： | 2A |
| 电源电压： | 4.5 V ~ 25 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-VFDFN |
| 供应商设备封装： | 6-DFN |
| 包装： | 盒 |
IXDR502 / IXDS502
Fig. 28
High State Output Resistance vs. Supply Voltage
Fig. 29
Low State Output Resistance vs. Supply Voltage
6
4.5
4
5
3.5
4
3
2.5
3
2
2
1.5
1
1
0.5
0
0
0
5
10
15
20
25
30
35
40
0
5
10
15
20
25
30
35
40
Supply Voltage (V)
Supply Voltage (V)
Supply Bypassing, Grounding Practices And Output Lead Inductance
When designing a circuit to drive a high speed MOSFET
utilizing the IXD_502, it is very important to observe certain
design criteria in order to optimize performance of the driver.
Particular attention needs to be paid to Supply Bypassing ,
Grounding , and minimizing the Output Lead Inductance .
Say, for example, we are using the IXD_502 to charge a 1500pF
capacitive load from 0 to 25 volts in 25ns .
Using the formula: I= ? V C / ? t, where ? V=25V C=1500pF &
? t=25ns, we can determine that to charge 1500pF to 25 volts in
25ns will take a constant current of 1.5A. (In reality, the charging
current won’t be constant, and will peak somewhere around
2A).
SUPPLY BYPASSING
In order for our design to turn the load on properly, the IXD_502
must be able to draw this 1.5A of current from the power supply
in the 25ns. This means that there must be very low impedance
between the driver and the power supply. The most common
method of achieving this low impedance is to bypass the power
supply at the driver with a capacitance value that is an order of
magnitude larger than the load capacitance. Usually, this would
be achieved by placing two different types of bypassing
capacitors, with complementary impedance curves, very close
to the driver itself. (These capacitors should be carefully selected
and should have low inductance, low resistance and high-pulse
current-service ratings). Lead lengths may radiate at high
frequency due to inductance, so care should be taken to keep
the lengths of the leads between these bypass capacitors and
the IXD_502 to an absolute minimum.
Copyright ? 2007 IXYS CORPORATION All rights reserved
GROUNDING
In order for the design to turn the load off properly, the IXD_502
must be able to drain this 1.5A of current into an adequate
grounding system. There are three paths for returning current
that need to be considered: Path #1 is between the IXD_502
and its load. Path #2 is between the IXD_502 and its power
supply. Path #3 is between the IXD_502 and whatever logic is
driving it. All three of these paths should be as low in resistance
and inductance as possible, and thus as short as practical. In
addition, every effort should be made to keep these three
ground paths distinctly separate. Otherwise, the returning ground
current from the load may develop a voltage that would have a
detrimental effect on the logic line driving the IXD_502.
OUTPUT LEAD INDUCTANCE
Of equal importance to Supply Bypassing and Grounding are
issues related to the Output Lead Inductance. Every effort
should be made to keep the leads between the driver and its
load as short and wide as possible. If the driver must be placed
farther than 2” (5mm) from the load, then the output leads should
be treated as transmission lines. In this case, a twisted-pair
should be considered, and the return line of each twisted pair
should be placed as close as possible to the ground pin of the
driver, and connected directly to the ground terminal of the load.
10
相关PDF资料 |
PDF描述 |
|---|---|
| IXI859S1 | IC REG/GATE DRIVER 3.3V 8-SOIC |
| JW-23-04-T-S-450-250 | CONN STACKER .156" 23POS SGL TIN |
| KA278R33CTU | IC REG LDO 3.3V 2A TO-220FL-4 |
| KA2803BD | IC EARTH LEAKAGE DETECTOR 8-SOP |
| KA2807 | IC GROUND FAULT INTERRUPTER 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IXDT30N120 | 功能描述:IGBT 晶体管 60 Amps 1200V 2.4 Rds RoHS:否 制造商:Fairchild Semiconductor 配置: 集电极—发射极最大电压 VCEO:650 V 集电极—射极饱和电压:2.3 V 栅极/发射极最大电压:20 V 在25 C的连续集电极电流:150 A 栅极—射极漏泄电流:400 nA 功率耗散:187 W 最大工作温度: 封装 / 箱体:TO-247 封装:Tube |
| IXDT30N120AU1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | IGBT | N-CHAN | 1.2KV V(BR)CES | 50A I(C) | TO-268AA |
| IXDT30N120D1 | 制造商:IXYS 制造商全称:IXYS Corporation 功能描述:High Voltage IGBT with optional Diode |
| IXE5216EC.C0 | 制造商:Intel 功能描述:Electronic Component |
| IXE611P1 | 功能描述:IC DRIVER MOSF/IGBT HALF 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
发布紧急采购，3分钟左右您将得到回复。