参数资料
| 型号： | KS8993F |
| 厂商： | Micrel Inc |
| 文件页数： | 36/99页 |
| 文件大小： | 0K |
| 描述： | IC CONV MED 10/100 3PORT 128PQFP |
| 标准包装： | 66 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 配用： | KS8993F-EVAL-ND - EVAL KIT EXPERIMENTAL KS8993F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
KS8993F
Micrel
August 26, 2004
Revision 1.0
- 41 -
the ingress port’s default tag. The default tags are programmed in register sets {19,20}, {35,36} and {51,52} for ports
1, 2 and 3, respectively. The KS8993F will not add tags to already tagged packets.
Tag removal is enabled by bit 1 of registers 16, 32 and 48 for ports 1, 2 and 3, respectively.
Optionally, the
Px_TAGRM strap-in pins can be used to enable this feature. At the egress port, tagged packets will have their 802.1Q
VLAN Tags removed. The KS8993F will not modify untagged packets.
The CRC is recalculated for both tag insertion and tag removal.
802.1p priority field re-mapping is a QoS feature that allows the KS8993F to set the “User Priority Ceiling” at any
ingress port. If the ingress packet’s priority field has a higher priority value than the default tag’s priority field of the
ingress port, the packet’s priority field is replaced with the default tag’s priority field. The “User Priority Ceiling” is
enabled by bit 3 of registers 16, 32 and 48 for ports 1, 2 and 3, respectively.
DiffServ based priority
DiffServ based priority uses registers 96 to 103. More details are provided at the beginning of the Advanced Control
Registers section.
2.9.4
Rate Limit Support
The KS8993F supports hardware rate limiting independently on the “receive side” and on the “transmit side” on a per
port basis. Rate limiting is supported in both priority and non-priority environment. The rate limit starts from 0 kbps
and goes up to the line rate in steps of 32 kbps. The KS8993F uses “one second” as the rate limiting interval. At the
beginning of each interval, the counter is cleared to zero, and the rate limit mechanism starts to count the number of
bytes during the interval.
On the “receive side”, if the number of bytes exceeds the programmed limit, the switch will stop receiving packets on
the port until the “one second” interval expires. Flow control can be enabled to prevent packet loss. If the rate limit is
programmed greater than or equal to 128 kbps and the byte counter is 8 Kbytes below the limit, flow control will be
triggered. If the rate limit is programmed lower than 128 kbps and the byte counter is 2 Kbytes below the limit, flow
control will also be triggered.
On the “transmit side”, if the number of bytes exceeds the programmed limit, the switch will stop transmitting packets
on the port until the “one second” interval expires.
If priority is enabled, the KS8993F can be programmed to support different rate limits for high priority packets and low
priority packets.
2.10 Configuration Interface
The KS8993F can operate as both a managed switch and an unmanaged switch.
In unmanaged mode, the KS8993F is typically programmed using an EEPROM.
If no EEPROM is present, the
KS8993F is configured using its default register settings. Some default register settings can be overridden via strap-in
pin options. The strap-in pins are indicated in the “KS8993F Pin Description and I/O Assignment” table in section 1.2.
相关PDF资料 |
PDF描述 |
|---|---|
| LFXP15E-5F256C | IC FPGA 15.4KLUTS 188I/O 256-BGA |
| LFXP15E-4F256I | IC FPGA 15.4KLUTS 188I/O 256-BGA |
| LFXP15C-5F256C | IC FPGA 15.5KLUTS 188I/O 256-BGA |
| LFXP15C-4F256I | IC FPGA 15.5KLUTS 188I/O 256-BGA |
| LFXP15E-4FN256I | IC FPGA 15.4KLUTS 256FPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KS8993F-A1 | 功能描述:IC CONV MED 10/100 3PORT 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KS8993FA5 | 功能描述:IC SWITCH 3-PORT 10/100 128-PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KS8993F-EVAL | 功能描述:EVAL KIT EXPERIMENTAL KS8993F RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| KS8993FL | 功能描述:IC CONV MED 10/100 SGL 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KS8993FL-EVAL | 功能描述:BOARD EVAL EXPERIMENT KS8993F RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。