收藏本站
参数资料
型号： KS8993F
厂商： Micrel Inc
文件页数： 37/99页
文件大小： 0K
描述： IC CONV MED 10/100 3PORT 128PQFP
标准包装： 66
系列： *
类型： *
应用： *
安装类型： 表面贴装
封装/外壳： 128-BFQFP
供应商设备封装： 128-PQFP（14x20）
配用： KS8993F-EVAL-ND - EVAL KIT EXPERIMENTAL KS8993F
KS8993F
Micrel
August 26, 2004
Revision 1.0
- 42 -
2.10.1 I
2C Master Serial Bus Configuration
With an additional I
2C (“2-wire”) EEPROM, the KS8993F can perform more advanced switch features like “broadcast
storm protection” and “rate control” without the need of an external processor.
For KS8993F I
2C Master configuration, the EEPROM stores the configuration data for register 0 to register 109 (as
defined in the KS8993F register map) with the exception of the “Read Only” status registers. After the de-assertion of
reset, the KS8993F will sequentially read in the configuration data for all 110 registers, starting from register 0. The
configuration access time (tprgm) is less than 15 ms, as depicted in the following figure.
Figure 7: KS8993F EEPROM Configuration Timing Diagram
....
RST_N
SCL
SDA
t
prgm<15 ms
The following is a sample procedure for programming the KS8993F with a pre-configured EEPROM:
1.
Connect the KS8993F to the EEPROM by joining the SCL and SDA signals of the respective devices. For the
KS8993F, SCL is pin 97 and SDA is pin 98.
2.
Enable I
2C master mode by setting the KS8993F strap-in pins, PS[1:0] (pins 100 and 101, respectively) to
“00”.
3.
Check to ensure that the KS8993F reset signal input, RST_N (pin 67), is properly connected to the external
reset source at the board level.
4.
Program the desired configuration data into the EEPROM.
5.
Place the EEPROM on the board and power up the board.
6.
Assert an active-low reset to the RST_N pin of the KS8993F. After reset is de-asserted, the KS8993F will
begin reading the configuration data from the EEPROM. The KS8993F will check that the first byte read from
the EEPROM is “93”.
If this value is correct, EEPROM configuration will continue.
If not, EEPROM
configuration access is denied and all other data sent from the EEPROM will be ignored by the KS8993F. The
configuration access time (tprgm) is less than 15 ms.
Note: For proper operation, check to ensure that the KS8993F PWRDN input signal (pin 36) is not asserted during
the
reset operation. The PWRDN input is active low.
相关PDF资料
PDF描述
LFXP15E-5F256C IC FPGA 15.4KLUTS 188I/O 256-BGA
LFXP15E-4F256I IC FPGA 15.4KLUTS 188I/O 256-BGA
LFXP15C-5F256C IC FPGA 15.5KLUTS 188I/O 256-BGA
LFXP15C-4F256I IC FPGA 15.5KLUTS 188I/O 256-BGA
LFXP15E-4FN256I IC FPGA 15.4KLUTS 256FPBGA
相关代理商/技术参数
参数描述
KS8993F-A1 功能描述:IC CONV MED 10/100 3PORT 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装
KS8993FA5 功能描述:IC SWITCH 3-PORT 10/100 128-PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装
KS8993F-EVAL 功能描述:EVAL KIT EXPERIMENTAL KS8993F RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
KS8993FL 功能描述:IC CONV MED 10/100 SGL 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装
KS8993FL-EVAL 功能描述:BOARD EVAL EXPERIMENT KS8993F RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*