- 您现在的位置：买卖IC网 > PDF目录10661 > KSZ8031RNL TR (Micrel Inc)TXRX PHY 100BASE TX 3.3V 24QFN PDF资料下载
参数资料
| 型号： | KSZ8031RNL TR |
| 厂商： | Micrel Inc |
| 文件页数： | 15/43页 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 100BASE TX 3.3V 24QFN |
| 标准包装： | 1 |
| 类型： | PHY 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RMII |
| 电源电压： | 1.8V，2.5V，3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（4x4） |
| 包装： | 标准包装 |
| 配用： | 576-3862-ND - BOARD EVALUATION FOR KSZ8031RNL |
| 其它名称： | 576-3843-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Micrel, Inc.
KSZ8021RNL / KSZ8031RNL
August 2010
22
M9999-082710-1.0
NAND Tree I/O Testing
The following procedure can be used to check for faults on the KSZ8021/31RNL digital I/O pin connections to the board:
1. Enable NAND tree mode by setting register 16h, bit [5] to ‘1’.
2. Use board logic to drive all KSZ8021/31RNL NAND tree input pins high.
3. Use board logic to drive each NAND tree input pin, per KSZ8021/31RNL NAND Tree pin order, as follow:
a. Toggle the first pin (MDIO) from high to low, and verify the TXD1 pin switch from low to high to indicate
that the first pin is connected properly.
b. Leave the first pin (MDIO) low.
c. Toggle the second pin (MDC) from high to low, and verify the TXD1 pin switch from high to low to indicate
that the second pin is connected properly.
d. Leave the first pin (MDIO) and the second pin (MDC) low.
e. Toggle the third pin from high to low, and verify the TXD1 pin switch from low to high to indicate that the
third pin is connected properly.
f.
Continue with this sequence until all KSZ8021/31RNL NAND tree input pins have been toggled.
Each KSZ8021/31RNL NAND tree input pin must cause the TXD1 output pin to toggle high-to-low or low-to-high to
indicate a good connection. If the TXD1 pin fails to toggle when the KSZ8021/31RNL input pin toggles from high to low,
then the input pin has a fault.
Power Management
The KSZ8021/31RNL offers the following power management modes:
Power Saving Mode
Power Saving Mode is used to reduce the transceiver power consumption when the cable is unplugged. It is enabled by
writing a one to register 1Fh, bit [10], and is in effect when auto-negotiation mode is enabled and cable is disconnected
(no link).
In this mode, the KSZ8021/31RNL turns off all transceiver blocks, except for transmitter, energy detect and PLL circuits.
By default, Power Saving Mode is disabled after power-up.
Energy Detect Power Down Mode
Energy Detect Power Down (EDPD) Mode is used to further reduce the transceiver power consumption when the cable is
un-plugged. It is enabled by writing a zero to register 18h, bit [11], and is in effect when auto-negotiation mode is enabled
and cable is disconnected (no link).
EDPD Mode works in conjunction with PLL off (set by writing a one to register 10h, bit [4] to turn PLL off automatically in
EDPD Mode) to turn off all KSZ8021/31RNL transceiver blocks, except for transmitter and energy detect circuits.
Further power consumption is achieved by extending the time interval in between transmissions of link pulses to check for
the presence of a link partner. The periodic transmission of link pulses is needed to ensure two link partners in the same
low power state and with auto MDI/MDI-X disabled can wake up when the cable is connected between them.
By default, Energy Detect Power Down Mode is disabled after power-up.
Power Down Mode
Power Down Mode is used to power down the KSZ8021/31RNL device when it is not in use after power-up. It is enabled
by writing a one to register 0h, bit [11].
In this mode, the KSZ8021/31RNL disables all internal functions, except for the MII management interface. The
KSZ8021/31RNL exits (disables) Power Down Mode after register 0h, bit [11] is set back to zero.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX981CSA+T | IC COMPARATOR OD 8-SOIC |
| VE-B1V-IV-F1 | CONVERTER MOD DC/DC 5.8V 150W |
| LTC1858CG#PBF | IC ADC 8CH 14BIT 100KSPS 28-SSOP |
| MAX972CSA+T | IC COMPARATOR OD 8-SOIC |
| VI-B1V-IV-F4 | CONVERTER MOD DC/DC 5.8V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8041FTL | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041FTL TR | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041FTL-EVAL | 功能描述:以太网开发工具 KSZ8041FTL Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8041FTLI | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041FTLI TR | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。