- 您现在的位置：买卖IC网 > PDF目录10661 > KSZ8031RNL TR (Micrel Inc)TXRX PHY 100BASE TX 3.3V 24QFN PDF资料下载
参数资料
| 型号： | KSZ8031RNL TR |
| 厂商： | Micrel Inc |
| 文件页数： | 4/43页 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 100BASE TX 3.3V 24QFN |
| 标准包装： | 1 |
| 类型： | PHY 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RMII |
| 电源电压： | 1.8V，2.5V，3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（4x4） |
| 包装： | 标准包装 |
| 配用： | 576-3862-ND - BOARD EVALUATION FOR KSZ8031RNL |
| 其它名称： | 576-3843-6 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Micrel, Inc.
KSZ8021RNL / KSZ8031RNL
August 2010
12
M9999-082710-1.0
Functional Description: 10Base-T/100Base-TX Transceiver
The KSZ8031RNL is an integrated single 3.3V supply Fast Ethernet transceiver. It is fully compliant with the IEEE 802.3
Specification. It reduces board cost and simplifies board layout by using on-chip termination resistors for the two
differential pairs and by integrating the regulator to supply the 1.2V core.
On the copper media side, the KSZ8031RNL supports 10Base-T and 100Base-TX for transmission and reception of data
over a standard CAT-5 unshielded twisted pair (UTP) cable, and HP auto MDI/MDI-X for reliable detection of and
correction for straight-through and crossover cables.
On the MAC side, the KSZ8031RNL provides the Reduced Media Independent Interface (RMII) for direct connection with
RMII-compliant Ethernet MAC processors and switches.
The MII management bus option gives the MAC processor complete access to the KSZ8031RNL control and status
registers. Additionally, an interrupt pin eliminates the need for the processor to poll for PHY status change.
As the power-up default, the KSZ8031RNL uses a 25MHz crystal to generate all required clocks, including the 50MHz
RMII reference clock output for the MAC. The KSZ8021RNL is the version which takes in the 50MHz RMII reference clock
as the power-up default.
The KSZ8021/31RNL is used to refer to both KSZ8021RNL and KSZ8031RNL versions in this data sheet.
100Base-TX Transmit
The 100Base-TX transmit function performs parallel-to-serial conversion, 4B/5B encoding, scrambling, NRZ-to-NRZI
conversion, and MLT3 encoding and transmission.
The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125MHz serial bit
stream. The data and control stream is then converted into 4B/5B coding and followed by a scrambler. The serialized data
is further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output. The output current is set by
an external 6.49k
Ω 1% resistor for the 1:1 transformer ratio.
The output signal has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot, and timing jitter. The wave-shaped 10Base-T output is also incorporated into the 100Base-TX
transmitter.
100Base-TX Receive
The 100Base-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data and
clock recovery, NRZI-to-NRZ conversion, de-scrambling, 4B/5B decoding, and serial-to-parallel conversion.
The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI) over the twisted pair
cable. Since the amplitude loss and phase distortion is a function of the cable length, the equalizer must adjust its
characteristics to optimize performance. In this design, the variable equalizer makes an initial estimation based upon
comparisons of incoming signal strength against some known cable characteristics, and then tunes itself for optimization.
This is an ongoing process and self-adjusts against environmental changes such as temperature variations.
Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used to
compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion circuit
converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then used
to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/5B
decoder. Finally, the NRZ serial data is converted to the MII format and provided as the input data to the MAC.
10Base-T Transmit
The 10Base-T drivers are incorporated with the 100Base-TX drivers to allow for transmission using the same magnetic.
The drivers perform internal wave-shaping and pre-emphasis, and output 10Base-T signals with a typical amplitude of
2.5V peak. The 10Base-T signals have harmonic contents that are at least 27dB below the fundamental frequency when
driven by an all-ones Manchester-encoded signal.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX981CSA+T | IC COMPARATOR OD 8-SOIC |
| VE-B1V-IV-F1 | CONVERTER MOD DC/DC 5.8V 150W |
| LTC1858CG#PBF | IC ADC 8CH 14BIT 100KSPS 28-SSOP |
| MAX972CSA+T | IC COMPARATOR OD 8-SOIC |
| VI-B1V-IV-F4 | CONVERTER MOD DC/DC 5.8V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8041FTL | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041FTL TR | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041FTL-EVAL | 功能描述:以太网开发工具 KSZ8041FTL Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8041FTLI | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041FTLI TR | 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。