- 您现在的位置：买卖IC网 > PDF目录11585 > KSZ8841-16MBL (Micrel Inc)IC MAC CTLR 1PORT ETH 100-LBGA PDF资料下载
参数资料
| 型号： | KSZ8841-16MBL |
| 厂商： | Micrel Inc |
| 文件页数： | 26/105页 |
| 文件大小： | 0K |
| 描述： | IC MAC CTLR 1PORT ETH 100-LBGA |
| 标准包装： | 260 |
| 控制器类型： | 以太网控制器，MAC |
| 接口： | 总线 |
| 电源电压： | 3.1 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LBGA |
| 供应商设备封装： | 100-LFBGA |
| 包装： | 托盘 |
| 产品目录页面： | 1080 (CN2011-ZH PDF) |
| 其它名称： | 576-3075 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页
Micrel, Inc.
KSZ8841-16/32 MQL/MVL/MBL
October 2007
27
M9999-102207-1.6
Functional Description
The KSZ8841M is a single-chip Fast Ethernet MAC controller consisting of a 10/100 physical layer transceiver (PHY), a
MAC, and a Bus Interface Unit (BIU) that controls the KSZ8841M via an 8-bit, 16-bit, or 32-bit host bus interface.
The KSZ8841M is fully compliant to IEEE802.3u standards.
Functional Overview
Power Management
Power down
The KSZ8841M features a port power-down mode. To save power, the user can power-down the port that is not in use by
setting bit 11 in either P1CR4 or P1MBCR register for this port. To bring the port back up, reset bit 11 in these registers.
In addition, there is a full chip power-down mode PWRDN (pin 36). When this pin is pulled-down, the entire chip powers
down. Transitioning this pin from pull-down to pull-up results in a power up and chip reset.
Wake-on-LAN
Wake-up frame events are used to wake the system whenever meaningful data is presented to the system over the
network. Examples of meaningful data include the reception of a Magic Packet, a management request from a remote
administrator, or simply network traffic directly targeted to the local system. In all of these instances, the network device is
pre-programmed by the policy owner or other software with information on how to identify wake frames from other network
traffic.
A wake-up event is a request for hardware and/or software external to the network device to put the system into a
powered state (working).
A wake-up signal is caused by:
1. Detection of a change in the network link state
2. Receipt of a network wake-up frame
3. Receipt of a Magic Packet
There are also other types of wake-up events that are not listed here as manufacturers may choose to implement these in
their own way.
Link Change
Link status wake events are useful to indicate a change in the network’s availability, especially when this change may
impact the level at which the system should re-enter the sleeping state. For example, a change from link off to link on may
trigger the system to re-enter sleep at a higher level (D2 versus D3
1) so that wake frames can be detected. Conversely, a
transition from link on to link off may trigger the system to re-enter sleep at a deeper level (D3 versus D2) since the
network is not currently available.
Wake-up Packet
Wake-up packets are certain types of packets with specific CRC values that a system recognizes as a ‘wake up’ frame.
The KSZ8841M supports up to four users defined wake-up frames as below:
1. Wake-up frame 0 is defined in registers 0x00-0x0A of Bank 4 and is enabled by bit 0 in wakeup frame control register.
2. Wake-up frame 1 is defined in registers 0x00-0x0A of Bank 5 and is enabled by bit 1 in wakeup frame control register.
3. Wake-up frame 2 is defined in registers 0x00-0x0A of Bank 6 and is enabled by bit 2 in wakeup frame control register.
4. Wake-up frame 4 is defined in registers 0x00-0x0A of Bank 7 and is enabled by bit 3 in wakeup frame control register.
Magic Packet
Magic Packet technology is used to remotely wake up a sleeping or powered off PC on a LAN. This is accomplished by
sending a specific packet of information, called a Magic Packet frame, to a node on the network. When a PC capable of
receiving the specific frame goes to sleep, it enables the Magic Packet RX mode in the LAN controller, and when the LAN
controller receives a Magic Packet frame, it will alert the system to wake up.
1 References to D0, D1, D2, and D3 are power management states defined in a similar fashion to the way they are defined for PCI. For
more information, refer to the PCI specification at www.pcisig.com/specifications/conventional/pcipm1.2.pdf.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12LCE518-04I/SM | IC MCU OTP 512X12 LV W/EE 8-SOIJ |
| PIC12CE519T-04/SN | IC MCU OTP 1KX12 W/EE 8SOIC |
| KSZ8841-16MQL | IC MAC CTRLR 8/16BIT 128-PQFP |
| PIC12CE518-04E/SM | IC MCU OTP 512X12 W/EE 8-SOIC |
| KSZ8895RQ | IC 10/100-T 5 PORT SW 128PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8841-16MBL-EVAL | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Single-Port Ethernet MAC Controller with Non-PCI Interface |
| KSZ8841-16MBLI | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-Bit) Bus Interface (I-Temp) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8841-16MQL | 功能描述:以太网 IC Single Ethernet Port + Generic (8, 16-bit) bus interface( Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8841-16MQL A6 | 功能描述:IC MAC CTRLR 8/16BIT 128-PQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| KSZ8841-16MQL-EVAL | 功能描述:以太网开发工具 KSZ8841-16MQL Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。