收藏本站
参数资料
型号： L6460TR
厂商： STMICROELECTRONICS
元件分类： 运动控制电子
英文描述： STEPPER MOTOR CONTROLLER, PQFP64
封装： 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件页数： 61/139页
文件大小： 3837K
代理商： L6460TR
Electrical specifications
L6460
28/139
Doc ID 17713 Rev 1
IAD
A/D path absorbed current
ADChannelX[4:0]
=10001 and
bit EnDacScale=0
-1
1
A
tDELAY
Delay from serial write to pin
low
CLOAD =50 pF
(45)
500
ns
SPI interface (40)
VIH
High level input voltage
(46)
1.6
V
VIL
Low level input voltage
(46)
0.8
V
VHYS
Input voltage hysteresis
(46)
0.15
0.22
V
VOH
High level output voltage
IOUT = -10mA,
(47)
2.75
V
VOL
Low level output voltage
IOUT = 10mA,
(47)
0.4
V
tSCLK
SCLK period
62.5
ns
tSCLK_rise
SCLK rise time
2
ns
tSCLK_fall
SCLK fall time
2
ns
tSCLK_high
SCLK high time
20
ns
tSCLK_low
SCLK low time
20
ns
tnSS_setup
nSS setup time
10
ns
tnSS_hold
nSS hold time
10
ns
tnSS_min
nSS high minimum time
30
ns
tMOSI_setup
MOSI setup time
10
ns
tMOSI_hold
MOSI hold time
10
ns
tMISO_rise
MISO rise time
CLOAD=50pF
(48)
9ns
tMISO_fall
MISO fall time
CLOAD=50pF
(48)
9ns
tMISO_valid
MISO valid from clock low
0
15
ns
tMISO_disable
MISO disable time
0
15
ns
CLOAD
MOSI maximum load
200
pF
1.
This value is useful to define the voltage rating for external capacitor to be connected from VSupply to VSupplyInt.
2.
This typical value is only intended to give an estimation of the current consumption when L6460 is configured in simple
regulators mode (see following Chapter 8.6.4) at the end of the start up sequence and with no load on regulators. This
typical value allows a raw choose of the external resistor but the definitive choose must be done according to the
recommendations on Chapter 4.1).
3.
Measured between 10% and 90% of output voltage transition.
4.
Measured from a fault detection to 50% of output voltage transition.
5.
Current is defined to be positive when flowing into the pin.
6.
Load regulation is calculated at a fixed junction temperature using short load pulses covering all the load current range. This
is to avoid change on output voltage due to heating effect.
7.
Undervoltage rising and falling thresholds are intended as a percentage of feedback pin voltage (VLINmain_FB).
8.
Default state.
9.
The regulated voltage can be calculated using the formula: VSWmain_OUT = VFBREF *(Ra+Rb)/Rb.
Table 5.
Electrical characteristics (continued)
Parameter
Description
Test condition
Min
Typ
Max
Unit
相关PDF资料
PDF描述
L6515 BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44
L6560AD 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560AD013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560D013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6562ATN SWITCHING CONTROLLER, PDIP8
相关代理商/技术参数
参数描述
L6470 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI
L64702QC-33 制造商:未知厂家 制造商全称:未知厂家 功能描述:
L64704 制造商:未知厂家 制造商全称:未知厂家 功能描述:L64704 Satellite Decoder technical manual 5/97
L6470H 功能描述:马达/运动/点火控制器和驱动器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
L6470HTR 功能描述:马达/运动/点火控制器和驱动器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*