- 您现在的位置：买卖IC网 > PDF目录43900 > L6460TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | L6460TR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PQFP64 |
| 封装： | 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64 |
| 文件页数： | 62/139页 |
| 文件大小： | 3837K |
| 代理商： | L6460TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页当前第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页
L6460
Electrical specifications
Doc ID 17713 Rev 1
29/139
10. Undervoltage rising and falling thresholds are intended as a percentage of feedback pin voltage (VSW_main_FB).
11. This condition is intended to simulate an extra current on output.
12. This condition is intended to simulate a short circuit on output.
13. Rise and fall time are measured between 10% and 90% VSWmain output voltage.
14. Undervoltage rising and falling thresholds are intended as a percentage of feedback pin voltage (VSWDRV_FB).
15. The current protection values must be intended as a protection for the chip and not as a continuous current limitation. The
protection is performed by switching off the output bridge when current reaches values higher than the IOC max. No
protection could be guaranteed for values in the middle range between IMAX and IOC
16. In this cell X stands for 1 or 2, Y stands for A or B
17. In this cell X stands for 3 or 4, Y stands for A or B
18. The current protection thresholds for Bridge 3 and 4 are not selectable so only the max current value
(MtrXSideYILimSel[1:0]= 11) is available.
19. Overcurrent Off time can be configured using SPI.
20. Rise and fall time are measured between 10% and 90% of DC output voltage. With device in full bridge configuration
(resistive load between outputs).
21. Default state for Aux1
22. Default state for Aux2
23. The regulated voltage can be calculated using the formula: VAUX_SW = VFBREF *(Ra+Rb)/Rb.
24. Undervoltage rising and falling thresholds are intended as a percentage of feedback pin voltage (GPIO1 and/or GPIO2)
25. Rise and fall time is measured between 10% and 90% of output voltage.
26. The external components connected to the pin must be chosen to avoid that the voltage exceeds this operative range.
27. The regulated voltage can be calculated using the formula: VAUX3_SW = VFBREF *(Ra+Rb)/Rb.
28. Undervoltage rising and falling thresholds are intended as a percentage of feedback pin voltage (VREF_FB).
29. The definition of LSB for this table is LSB=IMRmax/(27.5-1).
30. Integral Non Linearity error (INL) is defined as the maximum distance between any point of the ADC characteristic and the
“best straight line” approximating the ADC transfer curve.
31. The ADC ensures monotonic characteristic and no missing codes.
32. Differential nonlinearity error (DNL) is defined as the difference between an actual step width and the ideal width value of 1
LSB.
33. Offset error (OE) is the deviation of the first code transition (000...000 to 000...001) from the ideal (i.e. GND + 0.5 LSB).
34. Gain error (GE) is the deviation of the last code transition (111...110 to 111...111) from the ideal (V3v3 - 0.5 LSB), after
adjusting for offset error.
35. Please note that the result of the conversion will always be a 9-bit word: to speed up the conversion, the resolution is
reduced when the ADC is used in the 8- bit resolution mode.
36. Actual input capacitance depends on the pin that must be converted.
37. The definition of LSB for this table is LSB=IMRmax/(29-1).
38. All parameters are guaranteed in the range between VOL and VR Max.
39. Measured from DacValue[5:0] change in SPI interface.
40. VGPIO_SPI = 3.3 V unless otherwise specified
41. In this section reports the operational amplifier parameters that change when used as comparator.
42.
ΔVi is the differential voltage applied to input pins across the common voltage V
CM.
43. Measured between 50% of input and output signal.
44. Time measured from change in SPI interface to 50% of external pin transition.
45. Measured between nSS rising edge and 50% of Vout.
46. Specification applies to nSS, SCLK and MOSI pins.
47. Current is considered to be positive when flowing towards the IC
48. These times are measured at the pin output between specified VOH and VOL.
相关PDF资料 |
PDF描述 |
|---|---|
| L6515 | BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44 |
| L6560AD | 0.7 A POWER FACTOR CONTROLLER, PDSO8 |
| L6560AD013TR | 0.7 A POWER FACTOR CONTROLLER, PDSO8 |
| L6560D013TR | 0.7 A POWER FACTOR CONTROLLER, PDSO8 |
| L6562ATN | SWITCHING CONTROLLER, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6470 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI |
| L64702QC-33 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| L64704 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:L64704 Satellite Decoder technical manual 5/97 |
| L6470H | 功能描述:马达/运动/点火控制器和驱动器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6470HTR | 功能描述:马达/运动/点火控制器和驱动器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。