- 您现在的位置：买卖IC网 > PDF目录80167 > L99PM62XPTR (STMICROELECTRONICS) 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 PDF资料下载
参数资料
| 型号： | L99PM62XPTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 电源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| 封装： | ROHS COMPLIANT, POWERSSO-36 |
| 文件页数： | 31/98页 |
| 文件大小： | 1117K |
| 代理商： | L99PM62XPTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页
L99PM62XP
Protection and diagnosis
Doc ID 16363 Rev 2
3.3
High-side driver outputs
The component provides a total of 4 high-side outputs Out1 to 4, (7
Ω typ. at @ 25°C) to
drive e.g. LED's or hall sensors and 1 high-side output OUT_HS with 1
Ω typ. at @ 25 °C).
The high-side outputs switch off in case of:
●
Vs over and undervoltage
●
Over current
●
Overtemperature with pre warning(a)
In case of overload or over temperature (TSD1) condition, the drivers switchs off. The
according status bit is latched and can be read and optionally cleared by SPI. The drivers
remain off until the status is cleared.
In case over/under voltage condition, the drivers is switched off. The according status bit is
latched and can be read and optionally cleared by SPI. If the Vlockout bit (Control Register
4) is set to ‘1’ the drivers remain off until the status is cleared. If the Vlockout bit is set to ‘0’
the drivers switches on automatically if the error condition disappears.
In case of open-load condition, the according status register is latched. The status can be
read and optionally cleared by SPI. The high-sides not switches off.
For OUT_HS the auto recovery feature (OUTHSREC bit Control Register 4) can be enabled.
If this bit is set to ‘1’ the driver is automatically restart from a overload condition. This
overload recovery feature is intended for loads which have an initial current higher than the
over current limit of the output (e.g. Inrush current of cold light bulbs). During auto recovery
mode the over current status bit can not be read from SPI.
The device itself can not distinguish between a real overload and a non linear load like a
light bulb. A real overload condition can only be qualified by time. As an example, the micro
controller can switch on light bulbs by setting the over current recovery bit for the first 50ms.
After clearing the recovery bit, the output is automatically disabled if the overload condition
still exists.
In case of a fail safe condition, the high-side drivers are switched off. The control bits are set
to default values. (except OUT3/FSO if it is used as a high-side driver output)
Note:
The maximum voltage and current applied to the high-side outputs is specified in
Section 2.1: Voltage regulators. Appropriate external protection may be required in order to
respect these limits under application conditions.
3.4
Low-side driver outputs REL1, REL2
The outputs REL1, REL2 (RDSon = 2 Ω typ. @25 °C) are specially designed to drive relay
loads.
The outputs provide an active output zener clamping (45 V typ.) feature for the
demagnetization of the relay coil, even though a load dump condition exists.
For fail-safe reasons the relay drivers are linked with the fail safe operation: in case of
entering the fail safe mode, the relay drivers switchs off and the SPI control bits are set to
default (i.e. driver is off).
a.
Except OUT3 when configured as FSO.
相关PDF资料 |
PDF描述 |
|---|---|
| LSN-1.8/10-D3J | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-1.25/10-D3B | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LS4601-7EPD7TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS5540-7ERD9TB1 | 2-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS5540-7ERD5TB1 | 2-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L99PM72GXPTR | 功能描述:Automotive PMIC PowerSSO-36 制造商:stmicroelectronics 系列:- 包装:剪切带（CT） 零件状态:有效 应用:汽车级 电流 - 电源:6mA 电压 - 电源:6 V ~ 18 V 工作温度:-40°C ~ 130°C 安装类型:表面贴装 封装/外壳:36-??FSOP（0.295"，7.50mm 宽） 供应商器件封装:PowerSSO-36 标准包装:1 |
| L99SD01-E | 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Rail/Tube |
| L99SD01TR-E | 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Tape and Reel |
| L9A0212 | 制造商:LSI 制造商全称:LSI 功能描述:Microprocessor |
| L9D112G80BG4 | 制造商:LOGIC 制造商全称:LOGIC 功能描述:1.2 Gb, DDR - SDRAM Integrated Module |
发布紧急采购，3分钟左右您将得到回复。